Publicidad
INSTRUCTION
UK
These operating instructions should be read and
followed up carefully before utilizing the SUP board. Take
special care to follow up the correct sequence of inflating/
deflating of the assembling procedure.
CONTENTS
1 Inflatable Stand-Up paddleboard
1 Backpack
1 Aluminium adjustable paddle
1 Hand Pump
1 Leash. Length 230 cm
1 Detachable skeg
1 Repair kit
1
2
3
4
5
1. H3 Valve
2. Front bungee cord
3. Non slip EVA pad
4. Carry handle
5. Metal ring
6. Fixed skeg
7. Detachable skeg
WARNING
- SUP can be very dangerous and physically demanding.
The user of this product should understand that
participating in stand up paddling may involve serious
injury or death.
- Seek SUP instruction from a licensed or certified instructor.
- Always check weather forecasts prior to using the SUP
board. Never use the SUP board in thunderstorms and
lighting conditions.
- Always use appropriate protective gear and wear a
personal flotation device. Wear the correct protective
clothing for the conditions such as a wetsuit or a UV top.
Cold water and cold weather can result in hypothermia.
Always carry identification.
- Wear a helmet when appropriate.
- Do not exceed the maximum weight capacity of 100 kg.
- Do not operate the SUP board under the influence of
drugs and/or alcohol.
- This model is designed to be used in flat waters (lake,
rivers, sea shore) in standing and seating position. It is
not recommended to use the SUP board in high waves
nor for surfing.
- Beware of offshore winds and currents as they can take
you out to sea.
- Check your equipment prior to each use for signs of
wear, leaks or failure.
2 | Instructions for use – Stand-up paddleboard
- Tie the included leash to your SUP board at all times.
- Children should always be under adult supervision.
- Always inform someone your paddling route, the time
and place of departure and your intended time and
place of arrival. Paddling alone is not recommended.
- Watch out for other beach users especially swimmers
and children. Make sure you keep the SUP board and
paddle under control at all times.
PREPARATIONS FOR INFLATING THE SUP BOARD
Remove all sharp edged and pointed objects from the
surface in order to avoid damaging the SUP board.
ASSEMBLY INSTRUCTIONS / INFLATION / DEFLATION
Inflate the SUP board with the included hand pump.
- Unscrew the valve cap
approximately 90 degrees so it is in the "OUT" position.
- Insert the pump hose end piece and inflate it until you
will reach the required pressure. After inflation tighten
all the valve cap (clockwise). Only the valve cap can
ensure final AIR TIGHTNESS.
6
- To release air from the SUP board, remove the valve cap
and push the button
1
7
degrees so it is in the "IN" position.
The correct pressure for this SUP board is:
Maximum 1 bar / 15 PSI (=1000 mBar)
DO NOT EXCEED THIS !!
Using an electrical pump or air compressor is at your own
risk. This can lead to damaging the SUP board.
DETACHABLE SKEG ON BACKSIDE OF SUP BOARD
It is recommended to use the detachable skeg in deep
water, where it will allow you to move forward in a
straight line. Do not use it in shallow water because then
the skeg can hit the bottom. The Skeg can be placed on
the SUP board if this is inflated or deflated. To assemble
the skeg push the skeg in the black part on the back side
of the SUP board. To lock the skeg push the lock pin in the
skeg base hole.
ASSEMBLY INSTRUCTIONS INCLUDED PADDLE
The included paddle consists of 3 pieces.
1
2
3
1. Valve cap
1
2. Button
3. Valve base
2
3
. Push the button
in and turn
1
2
in and turn approximately 90
2
Lock pin
To adjust the paddle to the required length:
- Insert the bottom of pole
in to the top of pole
2
can be fixed when the pin on pole
hole of pole
.
3
- Open the button on top of pole
2
- Insert the bottom of pole
and choose the length that
1
suits you. Click the pin (behind the button) of pole
to the hole of pole
.
1
- The paddle length is adjustable from minimum length
1.68 mtr to maximum length 2.10 mtr.
ATTACHING THE LEASH
Before you start to use the SUP board first attach included
leash to the SUP board and yourself.
- Attach the leash to the metal ring on top of the SUP
board.
- Attach the other side of the lease to your ankle. When
you fall in the water the leash ensures that the SUP
board will not float away.
MAINTENANCE SUP BOARD
- Clean and check the SUP board and all accessories. Use
a mild, non scouring cleanser.
- Make sure the SUP board is completely dry before
placing it in the backpack. Otherwise this may cause
mold, foul odor and the skin/hull or the inside chambers
of the SUP board will suffer from water damage.
REPAIRS
Although the SUP board has been manufactured of a
reinforced and tough material, it is still possible to cause
holes or cracks when the SUP board is handled improperly.
For the repair of a small damage a repair kit is included.
- Prepare a round patch with repair material with correct
measurements.
- Clean the repair material and the area around the leak
with alcohol.
- Apply 3 thin, even coats of glue to both the surface
of the board and the repair material. Wait 5 minutes
between each coat.
- After the 3rd coat, wait 10-15 minutes before applying
the repair material. Use a handroller to apply the repair
material evenly. Pay special attention to the edges
- Wait at least 24 hours before re-inflating.
INSTRUCTIE
NL
Deze gebruiksaanwijzing dient zorgvuldig te
worden gelezen en opgevolgd. Volg de juiste volgorde op
voor het oppompen / leeglaten van het SUP board.
ACCESOIRES
1 Opblaasbaar SUP board
1 Rugzak
1 Aluminium in lengte verstelbare peddel
1 Hand Pomp
1 Koord. Lengte 230 cm
1 afneembare vin
1 Reparatie set
. This
3
is clicked in the
2
by pulling the button.
in
2
Publicidad
