Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
AX-ADFD01
Ford RSE/SYNC/THX
retention interface 2007-up
The AX-ADFD01 is designed to and must be used with the AX-ADBOX1 or
AX-ADBOX2 (sold seperately). Please refer to AX-ADBOX1 or AX-ADBOX2 for
16-pin connector instructions.
applIcatIons
ford
Edge
2007-2012
Escape
2008-2012
Expedition
2007-up
Explorer
2008-2011
Explorer Sport Trac
2008-2011
F-150
2009-up
F-250/350/450/550
2011-up
Five Hundred
2005-2007
Flex
2009-2012
Focus
2008-2011
Fusion
2007-2012
Taurus
2008-2012
Taurus X
2008-2009
Note: The SONY/THX sounds systems are digitally amplified
Interface components
22-pin harness to 24-pin Ford harness
tools requIred
• Cutting tool • Tape • Crimping tool
• Connectors (i.e. butt-connectors, bell caps, etc.)
METRA. The World's best kits.
Installation Instructions for AX-ADFD01
lIncoln
Mark LT
2007-2008
MKS
2009-2012
MKT
2010-2012
MKX
2008-2012
MKZ
2007-2012
Navigator
mercurY
Mariner
2008-2010
Milan
2008-2010
Mountaineer
2008-2010
Sable
2008-2009
LCD screen
™
1-800-221-0932
Caution
Metra recommends disconnecting the negative battery terminal before
beginning any installation. All accessories, switches, and especially air
bag indicator lights must be plugged in before reconnecting the battery
or cycling the ignition.
from the 16-pin harness with stripped leads (included with interface)
• Connect the White wire to the left front positive speaker output of the
aftermarket radio.
• Connect the White/Black wire to the left front negative speaker output of
the aftermarket radio.
• Connect the Gray wire to the right front positive speaker output of the
aftermarket radio.
2007-up
• Connect the Gray/Black wire to the right front negative speaker output of
the aftermarket radio.
Only make the following connections if the vehicle contains the SONY/THX
amplified system.
• Connect the Green wire to the radio's left rear positive speaker output.
• Connect the Green/Black wire to the radio's left rear negative speaker output.
• Connect the purple wire to the radio's right rear positive speaker output.
• Connect the purple/Black wire to the radio's right rear negative speaker output.
from the 22-way harness:
The din plug is to be connected to the included XIA-LCD screen if SYNC
information is shown on the OE radio.
metraonline.com
InstallInG tHe Interface
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
(continued on next page)
Publicidad
Manuales relacionados para Metra AX-ADFD01
Resumen de contenidos para Metra AX-ADFD01
- Página 1 2007-up bag indicator lights must be plugged in before reconnecting the battery The AX-ADFD01 is designed to and must be used with the AX-ADBOX1 or or cycling the ignition. AX-ADBOX2 (sold seperately). Please refer to AX-ADBOX1 or AX-ADBOX2 for 16-pin connector instructions.
- Página 2 AX-ADFD01 InstallInG tHe Interface Installing the aX-adfd01 (continued) 1. With all the connections completed, plug the 22- and 16-pin harnesses into the from the 24-way harness: AX-ADFD01. • Connect the Black wire to the ground wire of the aftermarket radio.
- Página 3 Interfase de retención RSE/SYNC/THX especialmente, las luces indicadoras de airbag deben estar enchufados El AX-ADFD01 está diseñado y deBe utilizarse con el AX-ADBOX1 o AX-ADBOX2 antes de volver a conectar la batería o comenzar el ciclo de ignición. (SE VENDE POR SEPARADO). Consulte el AX-ADBOX1 o AX-ADBOX2 para obtener instrucciones para el conector de 16 pins instalaCión de la interfase...
- Página 4 AX-ADFD01 instalaCión de la interfase instalación del aX-adfd01 (continúa) 1. Cuando termine todas las conexiones, conecte los arneses de 22 y 16 pins desde el arnés de 22 vías: al AX-ADFD01 El conector din debe conectarse a la pantalla XIA-LCD incluida si se muestra la 2.