Publicidad
Idiomas disponibles
Idiomas disponibles
Unplug the paint sprayer.
Leave intake tube and return tube in paint.
Gently pour 1/2 cup water over top of paint to prevent
drying.
Place the 5 gallon container lid on the paint container.
Wrap damp cloth around tubes and over opening of
container.
Wrap pistol-grip sprayer with damp cloth and place in
plastic bag. Seal bag.
Store for short time out of sunlight. For longer storage,
follow instructions for Cleaning the Paint Sprayer.
CLEANING THE PAINT SPRAYER
See Figures 16 - 17.
The solution used to clean the sprayer is determined by the
type of material that has been sprayed. For anything other
than latex material use Klean Strip
(for oil-based paints or varnish).
NOTICE:
It is important to thoroughly clean paint sprayer and
pistol-grip sprayer after each use or when changing paint
color. Allowing paint or stain to remain in an idle tool for
an extended period of time can cause its hoses to clog
and its moving parts to seize.
Always use drop cloths or other cover to protect areas
from possible spills.
Lock pistol-grip sprayer and follow Release Pressure
Procedure.
Unplug the paint sprayer.
Remove the spray tip and nozzle tip guard assembly from
sprayer.
Use cleaning brush (not included) to clean material from
spray tip holes.
Soak spray tip(s) and nozzle tip guard in water (for water
based paints) or Klean Strip® Green Safer Paint Thinner
(for oil-based paints or varnish), rinse.
Fill a bucket (waste container) with water (for water based
paints) or Klean Strip® Green Safer Paint Thinner (for
oil-based paints or varnish).
NOTE: If flushing or cleaning using water for water based
materials, It may be easier to use a garden hose and the
garden hose attachment (included). Remove filter from
intake tube and attach intake tube to garden hose with
attachment.
Place intake tube into the bucket of water (for latex
materials) or Klean Strip® Green Safer Paint Thinner (for
oil-based materials).
Place return tube into waste container.
Turn PRIME/SPRAY lever to PRIME.
Turn variable pressure control to PRIME.
Turn HI/OFF/FINISH switch to HI.
OPERATION
Green Safer Paint Thinner
®
13 — English
The paint sprayer will draw cleaning fluid up the intake tube
through the pump and out the return tube into the waste
container. Allow the cleaning fluid to run through the system
until it runs clear.
Turn prime/spray lever to SPRAY.
Unlock pistol-grip sprayer.
Point sprayer at the interior side of waste container to
flush out the high-pressure fluid hose and pistol-grip
sprayer.
NOTE: If using the garden hose adapter, turn on garden
hose and run water through system until water runs clear.
Leave system running for approximately one minute or
until cleaning fluid runs clear.
Turn prime/spray lever to PRIME.
Turn HI/OFF/FINISH switch to HI.
Unplug the paint sprayer.
Dispose of dirty water (or Klean Strip® Green Safer Paint
Thinner) in accordance with federal, state, and local
ordinances.
CLEANING THE PAINT SPRAYER WITH
GARDEN HOSE (FOR LATEX MATERIAL
ONLY)
See Figure 17.
Remove filter from intake tube.
Attach garden hose adaptor to garden hose.
Push garden hose adaptor onto the intake tube and
secure with butterfly clamp.
Turn PRIME/SPRAY to PRIME.
Turn variable pressure control to PRIME.
Turn on garden hose.
Turn HI/OFF/FINISH to HI.
Run water through system until clear water runs out of
the return tube.
Turn PRIME/SPRAY to SPRAY.
Unlock pistol-grip sprayer.
With the nozzle tip guard assembly removed, point the
pistol-grip sprayer at the interior side of waste container
to flush out the high-pressure fluid hose and pistol-grip
sprayer.
Leave the system running until clear water runs out of the
pistol-grip sprayer.
Turn PRIME/SPRAY lever to PRIME.
Turn HI/OFF/FINISH switch to OFF.
Unplug the paint sprayer.
Dispose of dirty water (or Klean Strip® Green Safer Paint
Thinner) in accordance with federal, state, and local
ordinances.
Publicidad
