Publicidad
Idiomas disponibles
Idiomas disponibles
E Instructions:
If you have any questions about your smart device, please contact
support: smartsupport@trixie.de.
• Read the operating instructions before use.
• The pet feeder is not a toy for children. Do not let children play with
the packaging foil. Danger of suffocation!
• The feeder is only suitable for dry food (diameter 5 - 15 mm).
• Do not use it with puppies and kittens under 7 months.
• The base unit must not get wet - not dishwasher suitable.
• Additional instructions for the use of IOT devices can be found at the
end of this manual.
Electric Shock Hazard!
• Incorrect use may result in electric shock.
• The mains voltage of the socket must match the specification on the
automatic feeder.
• Ideally, use an easily accessible socket so that you can quickly dis-
connect the feeder from the mains if necessary.
• Do not use the feeder if there is visible damage to the appliance or
the mains cable or plug.
• Do not open the feeder, but contact our customer service.
• Do not use a timer or other remote control system.
• Never touch the mains plug with wet hands.
Safety
• The feeder is suitable for indoor use only.
• Place the feeder on a level surface. The feeder must be sufficiently
ventilated on all sides.
• Only use the feeder with the feed container and lid and do not place
anything on top of it.
• Never pull the mains plug out of the socket by the cable, always
grasp the mains plug.
• Do not use the power cord as a carrying handle.
• Keep the feeder and power plug away from open flames and heat.
• Route the power cord so that it does not become a tripping hazard.
• Do not kink the power cord or place it over sharp edges.
• Do not allow your pet to nibble on the feeder or cord. If necessary,
protect it with a cord protector.
• Never reach for an electrical appliance if it has fallen into the water.
In such a case, unplug the appliance immediately.
• Unplug the feeder when not in use or when cleaning it.
Preparation
1. Press the latch on the top of the lid to open the feeder and remove
the accessories from the feeder container.
2. Connect the feeder to a power source using the mains plug or insert
three 3x D mono batteries into the battery compartment on the
underside of the feeder.
3. If you use the feeder with the mains power supply, you can still insert
batteries as an emergency power supply. That way the programmed
feeding times can be guaranteed even in the event of a power failure.
Key lock
Press and hold the
key for a few seconds to release or activate the key
lock. The key lock activates itself if no key is pressed for 30 seconds.
Setting the time
1. Unlock the control panel as described previously. Press „+" or „-" to
select between 24-hour count and 2-by-12-hour count. Finally, press
the
key briefly to confirm.
2. Now the hour digit of the current time flashes. Use +/- to set the cur-
rent hour and save the selection by pressing the
3. Next the minute digit of the current time flashes. Use +/- to set the
current minutes and save the selection by pressing the
Programming the feeding:
1. After setting the current time, the hour digit should flash again as
well as the small „1" at the bottom of the display. The flashing 1
indicates that it is now time to programme the first meal of the day.
2. Set the hour of the first feeding time with +/- and save the selection
by pressing the
key.
3. Now the minute digit of the first feeding time flashes. Use +/- to
set the minutes of the first feeding time and save the selection by
pressing the
key.
4. Finally, the portion size for the previously selected feeding time must
now be set. The value can be changed with +/- from 0 to max. 10
portions.
• P-00 means that no food is dispensed at the selected time.
• P-01 means that one portion (1 x 24 ml) is dispensed at the selected
time.
• P-10 means that ten portions (10 x 24 ml = 240 ml) are dispensed at
the selected time.
Please note that the portion size of 24 ml is a volume specification.
The effective weight of the food dispensed depends on the type of
food used.
Press the
key to confirm the portion size and complete the pro-
gramming of the first feeding time.
5. Repeat the previous steps for all four feeding times. If you want
fewer than four feeding times, you can complete the programming at
any time by pressing and holding the
Voice recording
The feeder allows you to create a voice recording that will play
each time the feeder ejects food. To record this, unlock the control
panel and press and hold the „Microphone" button to start a voice
recording. The red „STATE" LED lights up. Now you can speak in the
direction of the „MIC" opening for up to 10 seconds and make a voice
recording. The recording ends when the button is released. After a
successful recording, the „Bell" symbol appears in the display. Briefly
press the „Microphone" button to listen to the saved recording.
Repeat the previous steps to replace the recording with a new one.
Reset
Unlock the control panel and press the „ " and „-" keys simulta-
neously for 3 seconds to delete all feeding time settings and voice
recordings and reset the feeder to its default settings.
Filling the automatic feeder
1. Operate the latch on the top of the lid to open the automatic feeder.
Remove the foil from the desiccant bag and place it in the small
compartment on the inside of the lid. Insert the bowl by tilting the
feeder slightly backward, aligning the bowl, and snapping it into
place in the feeder housing.
2. Now fill the bowl with dry food and then trigger a manual feed by
releasing the key lock and then holding down „+". This ensures that
key again.
key again.
key.
5
Publicidad
