Hoover RC69PET Manual De Instrucciones página 7

3. Gently tap and wash the filter unit. Do not use hot water or detergents. Remove excess
water from the filter and leave to dry fully before using. [21,22]
4. Reassemble the Filter pack once it is fully dry and refit to the cleaner by inserting it
back into the location and pushing it fully home. [20]
5. Lock the exhaust filter cover by pressing the edge which has the clips, you will hear a
click once the exhaust filter door fits into place. [19]
IMPORTANT: Do not use the product without the filter pack fitted.
Cleaning the dust bin / separation unit
This cleaner uses a separation system unique to Hoover. If necessary the separation unit
can be disassembled from the dust bin and cleaned.
1. Press the dust bin release button and remove the dust bin assembly from the cleaner.
[14]
2. Hold the dust bin with one hand and with the other hand press the dust bin lid release
button to open the dust bin. [15]
3. Remove the Vortex Finder (Red) from the cyclone body. [16]
4. Remove the cyclone body from the dust bin. [17]
5. If necessary, use a cloth to remove excessive dust from the red vortex finder and the
cyclone body surface.
Place the dust bin under the tap. [21] Rinse with lukewarm water. Wash internal
6.
surfaces of the dust bin with water only. DO NOT use soap detergents to wash the
internals of the dust bin.
7. Reassemble the internal component to the dust bin, ensuring all components are dry.
8. Close over the dust bin lid and refit dust bin assembly to cleaner.
Removing a blockage
1. Check if the dust bin is full. If so refer to 'Emptying the dust bin.
2. If the dust bin is empty but suction is still low:
A. Do the filters need cleaning? If so refer to 'Cleaning the washable filters'.
B. Check if there is any other blockage in the system - Use a rod or pole to remove any
blockage from the extension tube or flexible hose.
C. Check if pre-motor filter is fitted.
D. Check if the separation unit needs to be cleaned. Refer to 'Cleaning the separation unit.
Replacing the battery of the handle remote control* [23]
If the remote controls on the handle do not respond when pressing any buttons,
please change the battery:
1. Use screw driver to release remote control from handle.
2. To replace the battery, push aside the clip, remove old batteries, replace and then refit
clip. Use only battery type Lithium CR2032 3V.
USER CHECK LIST
USER CHECKLIST
Should you have a problem with the product, complete this simple user checklist before
calling your local Hoover service.
• Is there a working electricity supply to the cleaner? Please check with another electrical
appliance.
• Is the dust bin over-filled? Please refer to 'Cleaner Maintenance'.
• Is the filter blocked? Please refer to 'Cleaner Maintenance'.
• Is the hose or nozzle blocked? Please refer to 'Removing a blockage from the system'.
• Has the cleaner overheated? If so, it will take approximately 30 minutes to automatically reset.
• Doesn't the remote control on the handle respond? Please refer to 'Replace the battery of
handle remote handle'.
IMPORTANT INFORMATION
Hoover spares and Consumables
Always replace parts with genuine Hoover spares. These are available from your local
Hoover dealer or direct from Hoover. When ordering parts always quote your model number.
Hoover Service
Should you require service at any time, please contact your local Hoover Service Office.
Quality
BSI ISO 9001: Hoover's factories have been independently assessed for quality. Our
products are made using a quality system which meets the requirements of ISO 9001.
Your Guarantee
The guarantee conditions for this appliance are as defined by our representative in the
country in which it is sold. Details regarding these conditions can be obtained from the
dealer from whom the appliance was purchased. The bill of sale or receipt must be
produced when making any claim under the terms of this guarantee.
Subject to change without notice.
4
GB