LUND 67705 Manual De Instrucciones página 10

GB
damaged components replaced with new ones that are free of defects.
Clean the product according to the instructions specifi ed in the "Product Maintenance" section.
The drive base must be placed on a level, fl at, hard and stable surface. All drive housing stands should be in contact with the
ground.
If the cup is not assembled with the blades, screw them to the base of the cup (II). Make sure that a gasket is fi tted between the
edge of the base of the cup and the blades (III). Without the gasket it will not be possible to ensure the tightness of the connection.
Check for leaks by pouring water into the cup. If they are detected, check the condition of the gasket to see if it is damaged or
distorted. Replace damaged or distorted seals with new ones.
Warning! Special care must be taken when handling the blades. Avoid contact with sharp edges. Using protective gloves is rec-
ommended. The blades may cause injury if they come into contact with the skin.
Mount the cup by placing it on the housing of the blender drive (IV).
The cup holder should hit the tab on the top wall of the drive housing.
The cup is equipped with a lid. The lid shall be mounted by placing it on the cup and then turning it in the direction indicating the
closed padlock symbol (V). The lid tab should be in line with the cup holder, and the hooks on the sides of the lid should slide
over the cup tabs (VI).
The device is equipped with a safety feature which prevents the blender from starting if the cup and/or lid are mounted incorrectly.
The lid is equipped with an additional plug, which allows you to add food products to the cup without removing the lid. Mount the
plug by pushing it into the lid opening.
Product operation
It is recommended to fi ll the cup with food when it is removed from the drive housing. This will prevent possible contamination of
the drive housing with food while the cup is being fi lled.
The cup should not be fi lled above the maximum capacity marker - the highest scale graduation described. Consider that the liquid
level in the cup will rise during stirring.
After fi lling, the cup should be covered with the lid with the plug installed.
Place the cup on the drive housing.
Make sure that the product switch is in the off position – O, then plug the power cord into the socket.
Start the product by changing the position of the switch to: 1 - 5 or P.
The switch positions marked as 1 to 5 start the blender and allow the device to operate at increasing speeds. The greater the
number, the higher the speed. The P position allows the maximum operating speed to be activated as long as the switch knob is
held in this position. When the knob is released, it will automatically return to the off position – O.
The operation is stopped after changing the position of the switch to the off position – O.
Before removing the cup, wait for the blades to stop completely, then unplug the power cord plug from the socket and remove the
cup from the drive housing.
It is recommended to use a lower rotational speed at the beginning of the operation, and then, if required, increase it gradually
during operation, until satisfactory results are obtained.
The product is designed to work continuously for no longer than 2 minutes. Next, wait for the product to cool down completely.
CAUTION! If the device begins to vibrate after switching it on, if it makes an unusual sound, or shows any other signs of malfunc-
tion, switch it off immediately, unplug it, and check for the cause of the malfunction.
Product maintenance
CAUTION! Before cleaning, switch the product off , unplug the power cord from the wall socket, wait for the unit to cool down, and
then proceed with maintenance.
CAUTION! It is recommended to clean the inside of the cup immediately after operation. This will prevent food residues from
drying up and make cleaning the product easier.
If the drive housing is contaminated with processed food during operation, stop your work, unplug the product by removing the
plug from the socket, clean the product, and only then resume operation.
Use only mild kitchen cleaning agents to clean the product. It is not allowed to use abrasive cleaning agents, e.g. cleaning powder
or milk, or agents containing corrosive substances. Do not use any solvents, petrol, or alcohol to clean the product.
Dilute the cleaning agent with water, according to the instructions supplied with the agent. Then, apply it on a soft cloth and clean
the drive housing on the outside.
Remove any residues of the cleaning agent with a soft cloth slightly soaked in clean water. Then, dry all surfaces with a dry soft cloth.
CAUTION! The drive housing is not designed for water jet cleaning. Do not immerse the drive housing in water.
Before fi rst use the inside of the cup only requires to be rinsed by fi lling it with water with a small amount of detergent, then empty
and repeat the operation, this time fi lling the cup with clean water, until the remains of detergent are rinsed out.
The inside of the cup and the blades should be cleaned after each operation by fi lling it with water with a small amount of deter-
gent. Then cover the lid with the plug installed and run the product for a short time.
Next, empty the cup and repeat the operation, this time using clean water. Repeat until you get rid of any residual detergent. Then
pour the water out of the cup and allow it to dry.
The cup can also be cleaned in a dishwasher, but the blades must be removed before placing the cup in the dishwasher.
O R I G I N A L I N S T R U C T I O N S
10