LUND 67705 Manual De Instrucciones página 9

GB
PRODUCT OVERVIEW
The bar blender is designed to prepare food. Thanks to its high power and capacious cup it is possible to prepare meals easily
and quickly by cutting and mixing food products. The cup with a sealed lid ensures a high level of cleanliness in the place of use.
The correct, reliable, and safe operation of the device depends on its proper use, which entails:
Reading and keeping the entire manual before the fi rst use of the product is necessary.
The supplier shall not be held liable for any damage resulting from failure to observe the safety regulations and recommendations
specifi ed in this manual. Use of the product for purposes other than those for which it was intended shall cause the loss of the
user's rights to the guarantee and under warranty.
ACCESSORIES
The product is delivered complete, but requires carrying out a number of preliminary actions described in further sections of the
manual, before starting operation.
The product comes with a cup and a lid with a plug.
SAFETY INSTRUCTIONS
Do not use the product in an explosive environment containing fl ammable liquids, gases, or vapours.
Before starting the product for the fi rst time, make sure that the product, its accessories, and the power cord have not been dam-
aged. If any damage is discovered, it is not allowed to start working with the product. Any damaged components, including the
power cord, must be replaced at an authorized facility. It is not allowed to repair the product on your own.
The product is intended for indoor use only. Do not expose the product to any precipitation or moisture. If water and moisture
enters the product, the risk of an electric shock is signifi cantly increased. Do not immerse the product in water or any other liquid.
Connect the product to the power network providing the voltages and frequencies indicated on the nameplate of the unit, exclu-
sively. The plug of the power cord must match the power socket. Do not modify the plug. Do not use any power adapters to adapt
the plug to the socket. An unmodifi ed plug, which matches the socket, reduces the risk of an electric shock.
After each application, unplug the power cord from the power socket. Always disconnect the blender from the power supply, if it is
left unattended, and before putting it away, disassembling, or cleaning.
Do not overload the power cord. Do not use the power cord to carry the product, connect, or disconnect the plug from the power
socket. Avoid any contact between the power cord and heat sources, oil, sharp edges, and moving parts. Damage to the power
cord increases the risk of an electric shock. If the power cord is damaged (e.g. it is cut, its insulation is melted), immediately unplug
it from the wall socket, and return it to an authorised service facility. It is not allowed to use the product with a damaged power cord.
It is not allowed to have the power cord repaired. It must be changed for a new one at an authorized service centre.
Disconnect the power cord from the power socket, before installing, removing, or adjusting any of the product accessories.
Exercise special care, when handling sharp parts of the product. Do not touch blades in motion. The blades are very sharp and
there is a risk of injury, even if the blades are not moving. Special care must be taken, when handling any accessories equipped
with blades.
Make sure that the cup has been installed correctly before starting the product.
Do not overload the product. The temperature of the housing must not exceed 60 C. Overloading the product will accelerate its
O
wear and tear, lead to its damaging, and increase the risk of an electric shock.
The product must be kept under supervision at all times during operation.
The product may not be used for hard food processing, seeds, bones, shells, ligneous parts of plants.
The product is not to be used by children. Keep the product and its power cord out of the reach of children. It is important to ensure
that children do not see the product as a toy.
Children should not be allowed to clean or maintain the product without the supervision of an adult.
This product cannot be used by people with impaired physical and/or mental abilities, and by people without any experience in or
understanding of the operation of the product, unless they are supervised or instructed in the safe use of the product, so that they
understand the relevant operating risks.
PRODUCT OPERATION
Preparing the appliance for operation
Caution! The procedure described in this section must be carried out when the device is unplugged from power supply. Make sure
that the power cord has been unplugged from the mains socket.
The product must be unpacked and all parts of the packaging completely removed. It is recommended to keep the packaging, as
it can be helpful for further transport and storage of the product.
Check the product for damage. If any damage is detected, do not use the product until the damage has been repaired or the
O R I G I N A L I N S T R U C T I O N S
9