Publicidad
Idiomas disponibles
Idiomas disponibles
Operating Instructions
Important Safety Instructions
(Continued)
Do not operate or
allow anyone else to
operate the tool if any
warnings or warning labels are not
legible. Warnings or warning labels
are located on the tool magazine
and body.
Do not drop or
throw the tool.
Dropping or throwing the tool can
result in damage that will make
the tool unusable or unsafe. If the
tool has been dropped or thrown,
examine the tool closely for bent,
cracked or broken parts and air
leaks. STOP and repair before using
or serious injury could occur.
Clean and check
all air supply
hoses and fittings before
connecting the tool to an air
supply. Replace any damaged
or worn hoses or fittings. Tool
performance or durability may be
reduced.
Do not use hand-
tool sockets. Use
impact quality sockets only. Hand
tool sockets are "glass-hard" and
will shatter and can cause serious
personal injury if used with air
tools.
Release
all pressure from the
system before attempting
to install, service, relocate
or perform any maintenance.
Do not misuse
this product.
Excessive exposure to vibration,
work in awkward positions, and
repetitive work motions can
cause injury to hands and arms.
Stop using any tool if discomfort,
numbness, tingling, or pain occur,
and consult a physician.
SERvICE
a. Tool service must be performed only
by qualified repair personnel.
b. When servicing a tool, use only
identical replacement parts. Use
only authorized parts.
c. Use only the lubricants supplied
with the tool or specified by the
manufacturer.
www.chpower.com
the tool without first obtaining
written approval from Campbell
WARNING
!
Hausfeld. Do not use the tool if
any shields or guards are removed
or altered. Do not use the tool as
a hammer. Personal injury or tool
damage may occur.
AIR SOURCE
a. Never connect to an air source that
is capable of exceeding 200 psi.
Over pressurizing the tool is able
to result in bursting, abnormal
operation, breakage of the tool or
serious injury to persons. Use only
clean, dry, regulated compressed air
at the rated pressure or within the
rated pressure range as marked on
the tool. Always verify prior to using
the tool that the air source has been
adjusted to the rated air pressure or
within the rated air-pressure range.
b. Never use oxygen, carbon dioxide,
combustible gases or any bottled
gas as an air source for the tool.
Such gases are capable of explosion
and serious injury to persons.
type of reactive gases,
including, but not
limited to, oxygen and
combustible gases, as a power
source. Use filtered, lubricated,
regulated compressed air only.
Use of a reactive gas instead of
compressed air may cause the tool
to explode which will cause death
or serious personal injury.
a pressure-regulated
compressed air source
to limit the air pressure
supplied to the tool. The regulated
pressure must not exceed 90 psi.
If the regulator fails, the pressure
delivered to the tool must not
exceed 200 psi. The tool could
explode which will cause death or
serious personal injury.
c. Do not exceed any pressure rating of
any component in the system.
SAvE THESE INSTRUCTIONS
Do not make any
modifications to
Do not
use any
O
CO
Use only
90 psi
DO NOT DISCARD
4
Operating Instructions
LUBRICATION
Proper lubrication is the owner's
responsibility. Failure to lubricate the air
tool properly will dramatically shorten
the life of the tool and will void the
warranty.
This impact
wrench requires
lubrication before the initial
use and before and after each
additional use.
Impact wrenches require lubrication
throughout the life of the tool and
must be lubricated in two separate
areas: the air motor and the impact
mechanism. Air tool oil is recommended
because this oil cleans, lubricates and
inhibits rust all in one step.
AIR MOTOR LUBRICATION
The motor must be lubricated daily. An
air motor cannot be oiled too often.
Disconnect the
impact wrench
from the air supply before
lubricating.
1. Disconnect the impact wrench from
the air supply.
2. Turn the impact wrench upside
2
down.
3. While pulling the trigger, squeeze
approximately a 1/4 oz. of airtool
oil in the air inlet. Then, push the
forward and reverse button in both
directions.
After an air
tool has been
lubricated, oil will discharge
through the exhaust port during
the first few seconds of operation.
Thus, THE EXHAUST PORT MUST BE
COVERED WITH A TOWEL before
applying air pressure. FAILURE TO
COVER THE EXHAUST PORT CAN
RESULT IN SERIOUS INJURY.
4. Connect the impact wrench to the
air supply and cover the exhaust port
with a towel. Run the impact wrench
in both the forward and reverse
directions for 20 to 30 seconds. Oil
will discharge from the exhaust port
when air pressure is applied.
Publicidad
