Publicidad
Idiomas disponibles
Idiomas disponibles
English
Correct Pressure Washer Unit Position
(Fig. A, D)
CAUTION: Before operation:
Always keep the unit right‑side up with its feet
wheels
15
on the ground as shown in Fig. D.
nOTE: Never attempt to use the pressure washer while
standing vertically, on its side, or flipped over on the ground.
Speed Selector Switch (Fig. A, Q)
This pressure washer gives you the choice to operate at a
high pressure or lower pressure for more delicate jobs, and
can also boost pressure for high‑performance cleaning.
The speed selector switch
‑
Off, centered.
HI, right side.
‑
‑
LO, left side.
To turn the pressure washer ON, toggle the speed selector
switch
9
to the right or left positions.
To turn the pressure washer OFF, toggle the speed selector
switch
9
to the center position.
For higher pressure washing, press the speed selector
switch
9
to the right to the "HI" position. This mode is best
for applications that need higher PSI.
For lower pressure washing, press the speed selector
switch
9
to the left to the "LO" position. This mode is best for
projects that require a more delicate cleaning. This mode also
generally offers more runtime.
nOTE: When in "HI" mode, runtime will be decreased as
compared to when pressure washer is in "LO" mode.
To activate Boost mode, press the boost button
green LED will illuminate when activated. This mode is best
for applications that require maximum available PSI.
nOTE: Boost mode will only function for up to ten minutes.
You can press the boost button
before ten minutes and you will go back to the mode the
speed selector switch
9
ten minutes the green LED will start to flash, and the unit will
return to the mode the speed selector switch
boost mode times out.
nOTE: After boost mode is used for a full ten minutes, the
unit can return to boost mode by re‑pressing the boost
button
19
.
nOTE: Overall runtime will be shortened by using
boost mode.
Pressure Washing (Fig. A–Q)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Preparing Surface for Cleaning
•
Remove objects from the area which could create a
hazard such as children's toys or outdoor furniture.
14
16
9
toggles to three positions;
19
again to exit boost mode
is set to. When you near the end of
9
is set to after
•
Ensure that all doors and windows are closed tight.
Protect all plants and trees in the adjacent area with a
drop cloth ensuring that they will not be harmed by
any overspray.
•
Pre‑rinse cleaning area with fresh water.
and
•
Use only detergents formulated for pressure washers.
•
Always test detergent in an inconspicuous area before use.
Preparing Pressure Washer Unit for Use
DANGER: Risk of fluid injection and laceration.
When using the high‑pressure setting, DO NOT allow
the high‑pressure spray to come in contact with
unprotected skin, eyes, or with any pets or animals.
Serious injury will occur.
CAUTION: Before operation:
1. Connect the high pressure hose to the pressure washer
and the pressure wand. For instructions on connecting
the high pressure hose to the pressure washer and
pressure wand, please refer to Attaching High Pressure
Hose under Assembly and Adjustments.
2. Connect the water supply to the pressure washer. For
instructions on connecting the water supply to the
pressure washer, please refer to Attaching Garden Hose
under Assembly and Adjustments.
3. Install the two battery packs
battery port door
into position, please refer to To Install the Battery Packs
under Installing and Removing the Battery Packs.
Preparing Spray Wand (Fig. A, G)
iMPORTAnT: Before turning on the pressure washer unit,
disengage the trigger lock‑off
19
, the
1. Spray wand must be assembled before use. Please
refer to Assembling Spray Wand under Assembly
and Adjustments.
2. Disengage the trigger lock‑off
3. Turn on the water supply.
4. Squeeze the trigger
purge the system of air.
5. If air is still found in the water stream, continue to run
water through the spray wand.
Cleaning a Surface (Fig. Q)
1. To start the pressure washer, toggle the speed selector
switch
2. The best angle for spraying water against a cleaning
surface is 45 °.
‑
Spraying head on tends to cause dirt particles to
imbed in the surface.
‑
When working on vertical surfaces, it is best to
apply detergent starting at the bottom and working
upwards which will prevent the detergent from
sliding down and causing streaks.
3. To disengage the spray handle, release the trigger.
34
. Ensure the door is fully latched
20
6
and squeeze the trigger
6
7
. Hold the trigger for 30 seconds to
9
to the HI or LO position.
. Close and lock the
7
.
.
Publicidad
