Publicidad
POWER INDICATOR ON THE MOWER (Fig. Q)
EN
The mower is equipped with a power indicator to indicate
the charge status of the battery pack and the working status
of the mower. The power indicator will illuminate when the
blade is rotating or when the LED headlights are turned on.
Fig. Q parts description see below:
Q-1
Power indicator
Power Indicator
Meaning
on Mower
Mower is
Shining green
working properly
Handle-Locking
Clamp/Quick-
Adjust Lever is
Flashing green
not triggered
properly
The battery is
Flashing red
depleted
The mower is
Solid orange
overheated
The mower is
Flashing orange
overloaded
Red and
Communication
green flashing
timeout
alternately
MOWER OVERLOAD PROTECTION
To prevent overload conditions, do not try to remove too
much grass at one time. Slow down your cutting pace or
raise the cut height.
Your mower has built-in overload circuit protection. When
the mower is overloaded, the motor will stop and the
power indicator on the mower will flash orange. Remove
the battery pack from the mower. Check to see if grass
has collected beneath the deck and clear it if necessary,
then install the battery and restart the mower.
BATTERY HIGH TEMPERATURE PROTECTION
The heat dissipates more slowly in hot weather. If the battery
temperature exceeds 70°C during operation, the protection
circuit will immediately turn off the mower to protect the
battery pack from damage. The power indicator on the
mower will shine orange and the LED on the battery will flash
orange. Release the bail handle, wait until the battery pack
cools down to approximately 67°C, then restart the mower.
16
56 VOLT LITHIUM-ION CORDLESS MOWER — LM1900E/LM1900E-SP
MAINTENANCE
remove the safety key from the mower before cleaning,
performing any maintenance or transporting the mower.
replacement parts. Use of any other parts may create
a hazard or cause product damage. To ensure safety
Action
and reliability, all repairs and replacements should be
performed by a qualified service technician.
N/A
GENERAL MAINTENANCE
Re-triggered the
handle-locking
pack when servicing or transporting the mower.
clamp/quick-adjust
Lever
The underside of mower deck should be cleaned after each
use, as grass clippings, leaves, dirt and other debris will
Stop the mower
accumulate.
and charge the
Remove any build-up of grass on or around the drive shaft
battery pack
and the motor fan (do not use water). Wipe the mower
Remove the
clean with a damp cloth.
battery from the
REMOVING/INSTALLING THE BLADE
mower, move them
to the shade and
cool them at least
heavy gloves or wrapping the cutting edges with rags or
15 minutes
other materials when performing any maintenance on
Slow down your
the mower blade. Always remove the battery pack when
pace or raise up
servicing or transporting the mower.
the cut height to
◾
To Remove the Blade
decrease the load
Following Fig. R1.
Connect EGO
NOTICE:
loosening the bolt, turn the fan by hand to align the through
holes in the fan with the holes in the blade, and place
another metal rod into the aligned holes (Fig. R2).
◾
To Install the Blade
Following the assembly sequence in Fig. S, with the
fan blade towards deck and the printed blade side
towards outside, align the through holes in the fan
with the holes in the blade (Fig. T) and then tighten the
blade as Fig. U shown.
Fig. R2 & S parts description see below:
R2-1 Stabilizer 1
R2-2 Stabilizer 2
R2-3 14mm Wrench
S-1
NOTICE:
blade bolt is 49-59Nm.
WARNING:
To avoid serious personal injury, always
WARNING:
When servicing, use only identical
WARNING:
Always remove the safety key and battery
WARNING:
Always protect your hands by wearing
If the bolt rotates with the motor shaft when
S-2
S-3
S-4
Fan
S-5
The recommended torque for tightening the
Inner Flange
Blade
Outer Flange
Bolt
Publicidad
