Publicidad
Idiomas disponibles
Idiomas disponibles
ASSEMBLY
WA R N I N G
R e c h a r g e o n l y w i t h
the charger specified for the battery. For
specific charging instructions, read the
operator's manual supplied with your charger
and battery.
Inserting the Battery into the Tool
Lock
Fig. 1
1
Unlock
Large slot
Large tab
Arrow
2
Line up the the large and small tabs on the battery
with the large and small slots in the tool opening.
Slide the battery all the way into the tool. Turn the
battery clockwise to lock it in place. The arrow on
the battery will line up with the
on the tool.
Removing the Battery from the Tool
Turn the battery cap counterclockwise to unlock.
The arrow on the battery will line up with the
on the tool. Pull the battery out of the tool.
Checking the Fuel Gauge
To determine the amount of charge left in the bat-
tery, press the forward/reverse switch. The Fuel
Gauge will light up for 2-3 seconds.
OPERATION
WARNING
Always remove battery
pack before changing or removing ac-
cessories. Only use accessories specifi cally
recommended for this tool. Others may be
hazardous.
WARNING
To reduce the risk of injury,
wear safety goggles or glasses with side-
shields.
Installing Bits
Always remove the battery before inserting or
removing bits. Select the proper style and size bit
for the type of screw you are using.
1. To install the bit, pull out the collar. Press the bit
into the socket until the collar snaps back and
the bit is locked into place.
2. To remove the bit, pull out the collar, then pull
out the bit.
NOTE: It is not necessary to hold the collar out
when installing and removing bits.
Adjusting the Handle
The handle is designed for convenience and con-
trol. The durable, center pivot allows the handle to
be used in the conventional shape or folded into
a pistol grip. Access to the forward/reverse switch
and lock switch is comfortable in either handle
position.
Fig. 2
+
-
Using the Adjustable Clutch
This tool has an adjustable
Fig. 3
clutch for driving different
types of screws into differ-
ent materials. When prop-
erly adjusted, the clutch will
slip at a preset torque to
prevent driving the screw
Driving
too deep and to prevent
damage to the screw or
Fig. 4
tool.
To adjust the clutch, turn
the clutch adjusting ring
so that the desired setting
(1-21) lines up with the ar-
row on the motor housing,
Drilling
as shown.
4
The torque specifications shown here are ap-
proximate values obtained with a fully charged
battery pack.
(in lbs
Clutch
Applications
Setting
Lo
Hi
1
3.3
3.3
Small screws in softwood.
4
6.3
6.3
Medium screws in soft-
wood or small screws in
7
9.0
9.0
hardwood.
10
11.4
11.4
Large screws in soft-
13
14.0
14.0
woods. Medium screws in
16
17.4
n/a*
hardwood or large screws
19
20.5
n/a*
in hardwood with pilot
hole.
Drilling
33.1
n/a*
* When set to high speed, set the clutch at 13 or
below. The Automatic Shut-Off may not work
at higher clutch settings (see "Automatic Shut-
Off").
NOTE: Because the settings shown in the table are
only a guide, use a piece of scrap material to test
the different clutch settings before driving screws
into the workpiece.
Using the Lock Switch
Fig. 5
Unlock
Lock
When the battery is installed, the tool is in operating
condition. The lock switch prevents accidental start-
ing by locking the forward/reverse switch. Always
set the lock switch to "lock" before performing
maintenance, changing accessories, storing the
tool and any time the tool is not in use.
1. To lock, push the lock switch toward the lock
symbol.
2. To unlock, push the lock switchtoward the unlock
symbol.
Selecting High or Low Speed
1. For low speed (200 RPM) and more torque, push
the speed selector back ("1" is displayed).
2. For high speed (600 RPM) and less torque, push
the speed selector forward ("2" is displayed).
Fig. 6
Low = 1
High = 2
Selecting Forward or Reverse
Fig. 7
Forward
+
Reverse
Press and hold the forward/reverse switch up for
forward rotation, and down for reverse rotation. The
switch will automatically return to the center, OFF
position when it is released.
Automatic Shut-Off
To prevent extra driving force after the selected
torque has been reached, the tool will automatically
shut off if the clutch slips. At higher clutch settings,
this feature may not immediately engage. Release
the switch to reset the automatic shut-off.
Cold Weather Operation
The MILWAUKEE Lithium-Ion batteries can be
used in temperatures down to -4°F. When the bat-
tery is very cold, it may "buzz" for the fi rst minute
of use to warm itself up. Put the battery on a tool
and use the tool in a light application. After about a
minute, the battery will have warmed itself up and
operate normally.
5
-
Publicidad
