Narex ASV 14 A Instrucciones De Uso Originales página 17

Torque setting
The necessary torque can be set by swiveling the adjusting ring (6) to-
wards the relevant symbol.
Screwing
Symbol 1 = min. torque
Symbol 20 = max. torque for screwing
Drilling
Symbol = max. torque
Tool clamping and releasing
By swiveling the clamping chuck sleeve (8), you open and close the
clamping jaws, which the working tool (bit, bit holder, etc.) is inserted
into. The devices are equipped by automatic spindle arrest (locking)
facilitating tool replacement, by using one hand only in the requested
direction.
Maintenance
Instructions for device cleaning
Start the motor and blow impurities and dust out of the vent holes of
the device. Use protective goggles for this operation. Clean the external
plastic parts by a wet rag and mild detergent. Though these parts are
made of the materials resistant to solvents, NEVER use any solvent.
Instructions for cleaning the charger
Impurities and dust can be removed from external charger surfaces by
a rag or a non-metal brush. Use neither water nor detergents.
WARNING!!
Prior to start cleaning, disconnect the charger from the power supply.
Accessories
The accessories recommended for use with the device are available
commercially in the shops with hand el. tools.
Storage
The packed device can be stored in a dry unheated store room where
the temperature does not drop below –5 °C.
Store the unpacked device in a dry store room where the temperature
does not drop below +5 °C and where abrupt temperature changes are
prevented.
Environmental protection
El. tools, accessories and packaging should be collected for subsequent
recovery, recycling and environmentally sound disposal.
For EU countries only:
Do not dispose the el. tools as the home waste!
In conformity with the European Directive 2002/96/EC on waste electri-
cal and electronic equipment and its implementation in national legisla-
tions the unusable dismantled el. tools should be collected for subse-
quent recovery, recycling and environmentally sound disposal.
Warranty
We grant warranty for material or workmanship defects of our devices
in conformity with mandatory provisions of the relevant country, but 12
months as a minimum. The warranty period of 24 months is valid in the
EU countries in case of the exclusively private scope of use (proved by
invoice or delivery note).
There is a 6-months warranty for battery cell.
The damages following from natural wear, overloading, incorrect han-
dling and/or the damages caused by the user or by using the device
contrary to the operating manual or the damages known upon pur-
chase are excluded from the warranty.
The complaints can be admitted only if the device is sent back to the
supplier or to the Authorized Service Center NAREX in the non-disman-
tled state. Keep the operating manual and proofs of purchase safely.
Otherwise the current warranty conditions and terms of the manufac-
turer are always valid.
Information about noise level and vibrations
The values have been measured in conformity with EN 60745.
Weighed sound pressure level L
In accuracy of measurements K = 3dB (A).
Weighed level of arm affecting vibrations is less than 2.5 m.s
In accuracy of measurements K = 1.5 m.s
Certificate of Conformity
ASV 14 A:
We declare that the device meets requirements of the following stan-
dards and directivesc.
Safety:
EN 60745–1; EN 60745–2–1
Directive 2006/42/EC
Electromagnetic compatibility:
EN 55014–1; EN 55014–2
Directive 2004/108/EC
2011
Narex s.r.o.
Chelčického 1932
470 01 Česká Lípa
Certificate of Conformity
AN-UNI:
We declare that the device meets requirements of the following stan-
dards and directivesc.
Safety:
EN 60335–1; EN 60335–2–29
Directive 2006/95/EC
Electromagnetic compatibility:
EN 55014–1; EN 55014–2;EN 61000–3–2; EN 61000–3–3
Directive 2004/108/EC
2009
Narex s.r.o.
Chelčického 1932
470 01 Česká Lípa
Changes are reserved
English
is less than 75 dB(A).
pA
-2
.
-2
Antonín Pomeisl
CEO of the company
12. 16. 2011
Antonín Pomeisl
CEO of the company
29. 12. 2009
.
17