Publicidad
Idiomas disponibles
Idiomas disponibles
DMX-512 connection / connection between fixtures
Projector 1
Starting address 1
Typ/Type/Type/Tipo: EUROLITE TS-150 DMX-scanner
Spannungsversorgung/Power supply/Aliment.: 230 V AC, 50 Hz ~
Ges. anschl. wert/Power cons./Puiss. de rendement/Cons.: 320 W
Sicherung/Fuse/Fusible/Fusible: F 8 A, 250 V
Lampe/Lamp/Lampe/Lámpara: CDM 230 V/150 W G-12
Vor Gebrauch Anleitung lesen. Lire le mode d'emploi avant l'utilisation.
Lea el manual del usuario antes de la puesta en marcha.
A
XLR occupation:
X
Y
1: Ground
T =45° C
T =60° C
a
B
2: Signal (–)
F
3: Signal (+)
0,5 m
®
eurolite
MADE IN CHINA
Out
B
C
LIGHTING CONTROL
PROTOCOL DMX-512
CAUTION, HOT LAMP!
Let the lamp cool down for 10 min.
In
Change the lamp by loose-
ning screws X and Y.
Adjust the lamp position by
turning screws A, B and C.
The wires must not come into contact with each other, otherwise
Please note, the starting address depends upon which controller is being used.
Only use a stereo shielded cable and 3-pin XLR-plugs and connectors in order to connect the controller with
the fixture or one fixture with another.
Occupation of the XLR-connection:
If you are using controllers with this occupation, you can connect the DMX-output of the controller directly
with the DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other
XLR-outputs, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always
connect one output with the input of the next fixture until all fixtures are connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120
between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
Addressing
Each projector occupies 6 channels. To ensure that the control signals are properly directed to each
projector, the projector requires adressing. This is to be done for every single projector by changing the DIP
switches as set out in this table.
The starting address is defined as the first channel from which the TS-7 will respond to the controller.
Please make sure that you don't have any overlapping channels in order to control each TS-7 correctly and
independently from any other fixture on the DMX data link. If two, three or more TS-7 are addressed
similarly, they will work similarly.
Projector 2
Starting address 7
Typ/Type/Type/Tipo: EUROLITE TS-150 DMX-scanner
Spannungsversorgung/Power supply/Aliment.: 230 V AC, 50 Hz ~
Ges. anschl. wert/Power cons./Puiss. de rendement/Cons.: 320 W
Sicherung/Fuse/Fusible/Fusible: F 8 A, 250 V
Lampe/Lamp/Lampe/Lámpara: CDM 230 V/150 W G-12
Vor Gebrauch Anleitung lesen. Lire le mode d'emploi avant l'utilisation.
Lea el manual del usuario antes de la puesta en marcha.
X
T =45° C
T =60° C
a
B
F
0,5 m
®
eurolite
MADE IN CHINA
B
LIGHTING CONTROL
PROTOCOL DMX-512
CAUTION, HOT LAMP!
Let the lamp cool down for 10 min.
Change the lamp by loose-
ning screws X and Y.
Adjust the lamp position by
turning screws A, B and C.
DMX-512 Controller
the fixtures will not work at all, or will not work properly.
A
XLR occupation:
Y
1: Ground
2: Signal (–)
3: Signal (+)
Out
C
In
24/53
Projector 3
Starting address 13
Typ/Type/Type/Tipo: EUROLITE TS-150 DMX-scanner
Spannungsversorgung/Power supply/Aliment.: 230 V AC, 50 Hz ~
Ges. anschl. wert/Power cons./Puiss. de rendement/Cons.: 320 W
Sicherung/Fuse/Fusible/Fusible: F 8 A, 250 V
Lampe/Lamp/Lampe/Lámpara: CDM 230 V/150 W G-12
Vor Gebrauch Anleitung lesen. Lire le mode d'emploi avant l'utilisation.
Lea el manual del usuario antes de la puesta en marcha.
A
XLR occupation:
X
Y
1: Ground
T =45° C
T =60° C
a
B
2: Signal (–)
F
3: Signal (+)
0,5 m
®
eurolite
MADE IN CHINA
Out
B
C
LIGHTING CONTROL
PROTOCOL DMX-512
CAUTION, HOT LAMP!
Let the lamp cool down for 10 min.
In
Change the lamp by loose-
ning screws X and Y.
Adjust the lamp position by
turning screws A, B and C.
51785814_V_2_0.DOC
120 Ohms
Ω
resistor
Publicidad
