Ryobi ETMS-1425 Manual De Utilización página 20

GB
F D
OPERATION (FIG. 1-9)
Switch on the saw.
■
Press the workpiece firmly against the stop rail (27)
■
and slowly slide it together with the cross stop (18)
against the blade (5) in order to make the cut.
When the cut is completed, switch off the saw.
■
Using as a mitre saw (Fig. 1-3, 10-13)
Convert the saw to mitre saw mode.
Settings (Fig. 1-3)
The machine head can be tilted a maximum of 45° to
■
the left by undoing the bevel lock knob (22).
The turntable (8) can be adjusted from -45° to +45°
■
by undoing the mitre lock knob (10).
On/Off switch (Fig. 1)
The saw is started by pressing the On/Off switch (3).
The switch has to be kept pressed while making the cut.
90° cross-cuts and 0° turntable (Fig. 10)
Convert the saw from table saw mode to mitre
■
saw mode.
Place the workpiece on the lower saw table (9) and
■
press it against the stop rail with your left hand.
Always position the material firmly on the machine
table so that it cannot move about while it is being cut.
Press the main switch (3) to turn on the saw.
■
Wait for the blade to reach its maximum speed before
■
starting the cut.
With the other hand, press the release button (1) and
■
lower the machine head by its handle (2) smoothly
and with slight pressure down through the workpiece
to make the cut.
When the cut is completed, return the machine to its
■
top parking position and let go of the On/Off switch.
CAUTION
A return spring causes the machine head to rise
automatically at the end of the cut. Do not let go of
the handle (2) as soon as the cut is completed but
steady the machine head and allow it to rise slowly.
90° cross-cuts and 0°-45° turntable (Fig. 11)
You can use the saw to make angled cuts of 0° to 45°
relative to the stop rail on the left and right side.
E I P NL S DK N FIN
English
Release the turntable (8) by slackening the mitre lock
■
knob (10) and pressing the catch (14).
Set the turntable (8) to the required angle by means
■
of the handle (2).
Re-tighten the mitre lock knob (10) to fasten the
■
turntable (8).
Mitre cuts 0°-45° and turntable 0° (Fig. 12)
You can use the saw to make left mitre cuts of 0° to 45°
relative to the work surface.
Lift the machine head to its top position.
■
Fix the turntable (8) in 0° position.
■
Undo the bevel lock knob (22) and tilt the machine
■
head by its handle (2) to the left until the mark (a)
on the machine head points to the required angle
dimension (b).
Re-tighten the bevel lock knob (22) make the cut.
■
Mitre cuts 0°-45° and turntable 0°-45° (Fig. 11/13)
You can use the saw to make left miter cuts of 0° to 45°
relative to the work surface and 0° to 45° relative to the
stop rail simultaneously (compound miter cuts).
Lift the machine head to its top position.
■
Release the turntable (8) by slackening the mitre lock
■
knob (10) and pressing the catch (14).
Adjust the turntable (8) by its handle (2) to the
■
required angle.
Re-tighten the mitre lock knob (10) to fasten the
■
turntable.
Undo the bevel lock knob (22) and tilt the machine
■
head by its handle (2) to the left to the required angle
dimension.
Re-tighten the bevel lock knob (22).
■
Chip extractor (Fig. 3)
The saw is equipped with a vacuum extraction socket
(31) for chips and dust.
It is easy therefore to connect the machine to a dust
extraction system.
REPLACING THE SAW BLADE (FIG. 14-19)
Pull out the power plug. The blade must stop moving
■
completely.
Set the saw to table mode.
■
Slacken the two Allen screws (38) and take off the
■
splitter (30) together with the upper blade guard (17).
Take out the recessed head screw (33) and the table
■
insert (34).
14
GR H CZ RUS RO PL