Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT:
-The interior vermiculite parts SHOULD NOT RECEIVE IMPACTS when refueling is
performed.
If any of these parts crack, but is properly set in its place, THE PROPER OPERATION OF
THE APPLIANCE SHALL NOT BE ALTERED AND THERE IS NO POTENTIAL RISK. The
equipment can be used normally. These cracks do not entail any manufacturing defect so
they do not fall under guarantee.
4.6 Loading and reloading of fuel. Do not exceed the maximum allowed load or reload. (See Table of Technical specifications).
4.7 Door opening. The door must be opened only for reloading. To open it, follow the steps described in pictures "C.1" and "C.2" on
page 9 of the ANNEXED document.
4.8 Operation in adverse weather conditions. It is possible for the device to malfunction due to sudden or unexpected weather
changes, causing: low pressure, ebb currents of air into the smoke duct. When these phenomena are observed it is advisable to close
the combustion register and turn the equipment off.
4.9 Fire Prevention. You must not place any flammable element outside the safety distance from the fireplace described in the table
in section 1.1 Technical specifications. You shall also take special precautions if there are children and elderly people present. In
case of fire, push away all the people around it, close the registers as much as possible and notify the Firefighting service.
4.10 Dilations of the sheet. Materials subject to temperature changes undergo dilatations. This phenomenon can cause sporadic
metallic noises more or less frequently. These are completely innocuous and do not mean any risk or problem for its operation.
5. MAINTENANCE AND CLEANING
5.1 Maintenance. An appropriate and regular maintenance of both the appliance and the installation contributes greatly
to its good performance. It is important to perform periodic and complete controls of the equipment and of the ducts and
installation. Thus, for your safety and comfort, some of our dealers offer a servicing contract for your device. Please
contact your dealer for this service.
5.1.1 Locking mechanisms. You need to make sure no mechanisms are locked after an extended shutdown period.
5.1.2. Spare parts. Use only original spare parts, or parts recommended by Manufacturas Rocal, S.A. See picture on
page 12 of the ANNEXED document.
5.2. Cleaning. It is important for the appliance to be clean of ash so that all mechanisms work properly. To clean the
body of the device use the cleaning dry cloth given with the appliance or similar. Do not use current cleaning products.
5.2.1 Glass. You must turn the device off to clean the glass. The products used must not come into contact with the
metal parts of the door or the ceramic board; the aggressiveness of these products can cause a corrosion process of
the equipment.
5.2.2 Ash box. Empty the box only when the appliance is completely turned off, ensuring that the ashes do not
contain any burning coals; in which case you should deposit them in a metal bucket. To access the ash basin follow
the steps shown in pictures C.1", "C.2 and "C.3" on page 9 of the ANNEXED document.
5.2.3. Flue liner. It is important to keep the flue liner clean. It gets dirty depending on the fuel used, on a slower or
faster combustion, etc. You need to clean the flue liner at least once per season. It is mandatory for a specialist to review
it periodically. To access the flue liner connector follow the steps shown in pictures "C.1", "C.2", "C.8" and "C.9" on pages
10 and 11 of the ANNEXED document.
CAUTION: With the appliance running, the inside compartment must remain completely closed. You can
only access it for ash disposal.
5.2.4. Painting. The heatproof paint that covers the inside and outside of the appliance withstands temperatures up to
600 °C and releases a subtle typical smell that disappears after the first few uses.
It is possible for the paint to jump out in some areas inside the housing after a period of use, due to corrosion caused
by liquids, inadequate fuel types or others not authorized by the manufacturer, etc., In that case it will be necessary to
repaint all damaged areas before a prolonged shutdown period. (Use exclusively "Rocal heatproof spray
6. PROBLEMS: CAUSE AND SOLUTION
Below is a table of possible anomalies, their causes and solutions:
PROBLEM
CAUSE
1. Rejects smoke and /
Incorrect duct
or insufficient draught
Lack of air supply for combustion
Incorrect position of registers
SOLUTION
Duct servicing*:
-connection
-diameter
-leaks
-insufficient length
-outdoor access
-possible elements blocking the exit
Check vents and / or outside air supply.
Simultaneous operation with other ventilation devices and / or heating
Setting the register
Pag. 10
Publicidad
