EINHELL 45.139.14 Manual De Instrucciones página 16

3. Proper use
The cordless drill driver is designed for tightening
and undoing screws in wood, as well as for drilling
in wood, metal and plastic.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Voltage supply ....................................... 18 V d.c.
Idling speed: ........................................ 0-550 rpm
Torque settings: ........................................... 21+1
Forward and reverse rotation ..........................yes
Chuck clamping width ......................... 0,8-10 mm
Battery charger output voltage: ............. 20 V d. c.
Battery charger output current: .................... 1.5 A
Mains voltage for charger: ..200-250 V~ 50-60 Hz
Battery type: .......................................Lithium-ion
Number of battery cells: .................................... 5
Battery capacitance: ................................. 1.5 Ah
Weight.......................................................1.35 kg
Max. screw diameter: .................................. 6 mm
The maximum screw diameter indicates the ma-
ximum diameter of the screw that can be screwed
into wood. The screw diameter can vary depen-
ding on the type of wood.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ................... 64.80 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 75.80 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Anl_TC_CD_18_35_Li_SPK13.indb 16 Anl_TC_CD_18_35_Li_SPK13.indb 16
GB
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Drilling in metal
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
- 16 -
= 4.890 m/s
2
h
2
10.02.2022 11:17:23 10.02.2022 11:17:23