LEGRAND HB3 B Serie Instrucciones De Instalación

No: 24139 – 06/17 rev. 2
Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: HB330-B, HB340-B, HB350-B, HB350C-B
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
HB3x0-B L1
The HB3x0 occupancy sensors are designed for automatic lighting control in warehouse high bay applications. All models contain a
passive infrared sensor (PIR). The HB3x0-B series sensors are modular and are made up of two parts, a Power Module (HB3x0-B) and
a Lens (HBLx). The coverage area is determined by the lens module. The lenses are interchangeable with any HB3xx series sensor.
See the HBLx Lens Coverage Guide, available at http://www.legrand.us/wattstopper for more information.
All models in the HB3x0-B series use a set of DIP switches to set the time delay, PIR sensitivity, and occupancy sensing overrides.
• The HB330 contains two relays for controlling both phases of a 208VAC or 240VAC load.
• The HB340 contains two relays for controlling both phases of a 480VAC load or a single 347VAC load.
• The HB350 provides a single load controlling relay.
• The HB350C-B is for colder ambient temperature applications: -40° to 131°F (-40° to 55°C)
Coverage patterns, density and range, are determined by the type of Lens attached to the HB3x0-B.
For a complete description of each lens coverage pattern, see the HBLx Lens Coverage Guide.
1. Determine the mounting location appropriate to the features of the
power module and the coverage area. Careful consideration must be
given to sensor placement. Avoid placing the sensor where shelving or
other obstructions may block the sensor's line of sight.
2. Make sure that you have the appropriate accessories for the sensor
mounting configuration. (See Mounting Options.)
3. Assemble any necessary mounting accessories and attach them to the power module, making sure that the flying leads from the
power module are accessible.
4. Connect the line voltage and load wires to the power pack leads as shown in the Wiring Diagram for the unit's application.
• Do not allow bare wire to show.
• Make sure all connections are secure.
5. Attach the Lens to the HB3x0-B.
6. Restore power from the circuit breaker.
HB3x0-B L2/
HB3x0-B L3
HB3x0-B L7
DESCRIPTION AND OPERATION
Wattstopper
High Bay • Low Voltage • Passive Infrared Occupancy Sensor Power Module
Grande hauteur • Basse tension • Infrarouge passif Module d'alimentation
du détecteur de présence
Módulo de alimentación •de bajo voltaje • para el sensor de ocupación
infrarrojo pasivo para áreas de almacenamiento elevadas
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación
HB330-B Power Module
Voltage ................................................ 208/240VAC, 60Hz
Load Ratings (each relay)
HB340-B Power Module
Voltage ................................................ 347/480VAC, 60Hz
Load Ratings
HB350-B Power Module
Voltage ................................................ 120/277VAC, 60Hz
Load Ratings (each relay)
U.S. Patents: .............................5,640,113 and 5,804,991
COVERAGE
INSTALLATION
®
SPECIFICATIONS
@ 208VAC, 60Hz ................................. 5AMP ballast
@ 240VAC, 60Hz ................................. 5AMP ballast
@ 347VAC, 60Hz ................................. 5AMP ballast
@ 480VAC, 60Hz ................................. 5AMP ballast
@ 120 VAC, 60Hz .......... 0-800W ballast or tungsten
@ 277 VAC, 60Hz ............................0-1200W ballast
@ 120 VAC ......................................................1/6 hp
WARNING: TURN THE POWER
OFF AT THE CIRCUIT BREAKER
BEFORE WIRING THE SENSOR.