Bosch EasyAquatak 120 Manual Original página 17

Mounting and Operation
Representation/Action Ob-
jective
Delivery scope EasyAquatak
100
Delivery scope EasyAquatak
110/120
Mounting cable bracket/in use
storage for gun
Connecting/disconnecting high
pressure gun to lance
Connecting/disconnecting
nozzle
Connecting/disconnecting high
pressure water supply hose/
nozzle
Connecting to the water supply
Switching On and Off
Attaching Nozzle
Adjust water jet
Connect detergent bottle
Clean nozzle
Clean the filter
Transport
Storage
Selecting accessories
Switching on
For Your Safety
Warning: Switch off, remove plug from
mains before adjusting, cleaning or if cable
is cut, damaged or entangled.
The operating voltage is 230 V AC, 50 Hz (for non-EU coun-
tries 220 V, 240 V as applicable). Contact your Bosch Ser-
vice Centre for details. If in doubt contact a qualified electri-
cian or the nearest Bosch Service Centre.
If you want to use an extension cable when operating your
high pressure washer, only the following cable dimensions
should be used:
2
– 2.5 mm – max length 25 m
Note: If an extension cable is used it must be earthed and
connected through the plug to the earth cable of your supply
network in accordance with prescribed safety regulations.
If in doubt contact a qualified electrician or the nearest
Bosch Service Centre.
WARNING! Inadequate extension cables can
be dangerous. Extension cable, plug and
socket must be of watertight construction
and intended for outdoor use.
Bosch Power Tools
The connections (plugs and sockets) should be kept dry and
off the ground.
For increased electrical safety use a Residual Current Device
Figure Page
(RCD) with a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.
A 279
If the supply cord is damaged, it must be replaced by a
Bosch Service Centre.
B 280
For products not sold in GB:
Warning: For your safety, it is required that the plug at-
C 281
tached to the product is connected with the extension cord.
The coupling of the extension cord must be protected
against splash water, be made of rubber or coated with rub-
D 281
ber. The extension cord must be used with a cable strain re-
lief.
E 282
To prevent damage to the appliance, do not allow it to oper-
ate dry.
F 282
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
G 283
If the plug is not suitable for your socket outlets, it should be
H 283
cut off and an appropriate plug fitted in its place by an au-
I 284
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
J 285
shock hazard and should never be inserted into a mains
K 286
socket elsewhere.
L 286
Operation
M 287
N 287 To prevent damage to the appliance, do not allow it to
u
operate dry.
O 288
Starting
Attach water supply hose (not supplied) to the mains water
supply and machine.
Connect the product to the mains supply ensuring that the
mains switch is in the off position.
Open water tap.
Press the safety lock (back button on the gun handle) to re-
lease the trigger. Fully press the trigger until there is a con-
stant flow of water to clear the air from the machine and wa-
ter supply hose. Release trigger. Press the safety lock (front
button on the gun handle).
Turn button on main switch. Point the power gun down-
wards. Press the trigger safety lock to release the trigger.
Fully press the trigger.
Autostop Function
The machine is designed to switch off the motor when the
trigger is released on the gun.
Working Advice
General
Never use a roto nozzle or pencil jet to clean motor
u
vehicles.
English | 17
F 016 L94 016 | (17.01.2020)