Descargar Imprimir esta página

Bosch EasyAquatak 120 Manual Original página 18

Ocultar thumbs Ver también para EasyAquatak 120:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 30
18 | English
Ensure that the pressure washer is on level ground.
Do not overreach with the high pressure hose or move the
pressure washer by pulling the hose, this could cause the
ma-chine to become unstable and fall over.
Do not kink or drive a motor vehicle over the high pressure
hose. Do not expose the high pressure hose to sharp edges
or corners.
Working advice for cleaning with detergents
Only use cleaning agents suitable specifically for high
u
pressure washers.
We recommend that you use detergent sparingly for the sake
of the environment. Observe the recommended dilution on
the detergent label.
The high-pressure foam nozzle supplied with this product in-
cludes a regulator to control detergent use. Adjust as re-
quired.
Recommended cleaning method
Step 1: Attach the fan nozzle and remove the heavy dirt.
Only for EasyAquatak 110/120:
Step 2: Attach the foam bottle and spray on the detergent
sparingly.
Step 3: Rinse off the loosened dirt and detergent with the
fan nozzle.
Note: When cleaning a vertical surface spray off dirt/deter-
gent from the bottom and work in an upwards direction.
Rinse from the top and work downwards.
Use with alternative water sources
This high-pressure washer will self prime and can draw water
from water tanks and natural water sources. It is IMPORT-
Troubleshooting
Problem
Possible Cause
Motor refuses to start
Plug not connected
Mains socket faulty
Fuse faulty / blown
Extension cable damaged
Motor protector has activated
Frozen
Motor stops
Fuse faulty / blown
Wrong mains voltage
Motor protector has activated
Fuses blow
Fuses incorrectly rated
Motor starts but no
Nozzle partly blocked
pressure
Motor "sounds" but
Insufficient power supply
fails to start
F 016 L94 016 | (17.01.2020)
ANT that the water is clean and the BOSCH inlet filter is clear
and fitted to the machine.
Open tanks/containers and natural water
sources
Use the Self Priming accessory kit comprising:
– Inlet strainer with non return valve
– 3 m reinforced supply hose
– Universal coupling to the pressure washer
This enables the pressure washer to draw water up to 0.5 m
above the water level in the source. This may take up to 15
seconds.
Submerge the 3 m hose in water to displace the air. Connect
the 3 m supply hose to the pressure washer ensuring that
the inlet strainer remains submerged in the water source.
Run the pressure washer with the lance disconnected until a
steady flow of water appears from the high pressure hose.
Stop if this has not been achieved within 25  seconds and
check all the connections. Switch off and connect the lance
and nozzle to operate.
It is important to ensure that all hose and coupling connec-
tions are of good quality, air tight and that all washers are in
good condition and correctly seated in place. Failure to do
so may affect the self priming performance.
Water Tanks with outlet connections
When connecting the pressure washer to a water tank with a
suitable tap outlet, first connect the supply hose (not
provided) to the tank outlet, open the tap to allow the water
to displace all the air in the hose and then connect to the
pressure washer.
Corrective Action
Connect plug
Use another socket
Replace fuse
Try without extension cable
Allow to cool for 15 minutes
Wait for pump/water supply hose/accessory to
thaw
Replace fuse
Check that mains voltage corresponds to specific-
ations on the model tag
Allow to cool for 15 minutes
Change to a mains supply higher than the pres-
sure washer amp consumption
Clean nozzle
Check that the voltage of the mains power supply
line is the same as that on the plate.
Bosch Power Tools

Publicidad

loading