Descargar Imprimir esta página

Bosch PBH 2900 FRE Manual Original página 24

Ocultar thumbs Ver también para PBH 2900 FRE:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 44
OBJ_BUCH-318-002.book Page 24 Thursday, September 3, 2009 10:01 AM
24 | English
Assembly
Before any work on the machine itself, pull
the mains plug.
Auxiliary Handle
Operate your machine only with the auxilia-
ry handle 17.
Rotating the Auxiliary Handle (see figure A)
The auxiliary handle 17 can be set to any posi-
tion for a secure and low-fatigue working pos-
ture.
– Turn the wing bolt for adjustment of the aux-
iliary handle 16 in anticlockwise direction
and set the auxiliary handle 17 to the re-
quired position. Then tighten the wing bolt
16 again in clockwise direction.
Adjusting the Drilling Depth (see figure B)
The required drilling depth X can be set with the
depth stop 18.
– Press the button for the depth stop adjust-
ment 15 and insert the depth stop into the
auxiliary handle 17.
The knurled surface of the depth stop 18
must face downward.
– Insert the SDS-plus drilling tool to the stop
into the SDS-plus tool holder 3. Otherwise,
the movability of the SDS-plus drilling tool
can lead to incorrect adjustment of the drill-
ing depth.
– Pull out the depth stop until the distance be-
tween the tip of the drill bit and the tip of the
depth stop correspond with the desired drill-
ing depth X.
Selecting Drill Chucks and Tools
For hammer drilling and chiselling, SDS-plus
tools are required that are inserted in the SDS-
plus drill chuck.
For drilling without impact in wood, metal, ce-
ramic and plastic as well as for screwdriving and
thread cutting, tools without SDS-plus are used
(e.g., drills with cylindrical shank). For these
tools, a keyless chuck or a key type drill chuck
are required.
1 609 929 T39 | (3.9.09)
PBH 3000-2 FRE: The SDS-plus quick change
chuck 2 can easily be replaced against the quick
change keyless chuck 1 provided.
Replacing the Drill Chuck
(PBH 2800 RE/ PBH 2900 FRE/
PBH 3000 FRE Set)
To work with drilling tools without SDS-plus
(e. g., drill bits with cylindrical shank), the key
type drill chuck or the keyless chuck must be
mounted.
Mounting the Key Type Drill Chuck
(Accessory) (PBH 2800 RE) (see figure C)
– Screw the SDS-plus adapter shank 22 into a
key type drill chuck 21. Secure the key type
drill chuck 21 with the securing screw 20.
Please observe that the securing screw has
a left-hand thread.
Inserting the Key Type Drill Chuck or the Key-
less Chuck (see figure D)
– Clean the shank end of the adapter shank
and apply a light coat of grease.
– Insert the key type drill chuck 21 or the key-
less chuck 23 with the adapter shank into the
tool holder with a turning motion until it au-
tomatically locks.
– Check the locking effect by pulling the key
type drill chuck or the keyless chuck.
Removing the Key Type Drill Chuck or the Key-
less Chuck
– Push the locking sleeve 5 toward the rear
and pull out the key type drill chuck 21 or the
keyless chuck 23.
Removing/Inserting the Quick Change
Chuck (PBH 3000-2 FRE)
Removing the Quick Change Chuck
(see figure E)
– Grasp the lock ring of the quick change
chuck 6 and pull it firmly in the direction of
the arrow. The quick change chuck is re-
leased and can be removed toward the front.
– After removing, protect the replacement
chuck against contamination.
Bosch Power Tools

Publicidad

loading

Este manual también es adecuado para:

Pbh 2800 rePbh 3000 fre setPbh 3000-2 fre