Publicidad
Idiomas disponibles
Idiomas disponibles
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this tool, go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store or
Google Play from your smart device.
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Selecting Drill or Drive Action
(Cat. No. 2905-20)
1. To use the drilling mode, rotate
the torque selector collar until the
drill symbol
appears in line
with the arrow.
2. To use the driving mode rotate
the torque selector collar until the
desired clutch setting appears in
line with the arrow.
The adjustable clutch, when
properly adjusted, will slip at a
preset torque to prevent driving
the screw too deep into different materials and to
prevent damage to the screw or tool.
Selecting Hammer, Drill or Drive Action
(Cat. No. 2906-20 )
1. To use the hammer-drilling
mode, rotate the torque selector
collar until the hammer symbol
appears in line with the ar-
row. Apply pressure to the bit to
engage the hammering mecha-
nism.
When using carbide bits, do not use
NOTICE
water to settle dust. Do not attempt
to drill through steel reinforcing rods. This will
damage the carbide bits.
2. To use the drilling only mode,
rotate the torque selector collar
until the drill symbol
in line with the arrow.
3. To use the driving screws
mode, rotate the torque selector
collar until the desired clutch set-
ting appears in line with the
arrow.
The adjustable clutch, when
properly adjusted, will slip at a
preset torque to prevent driving the screw too deep
into different materials and to prevent damage to
the screw or tool.
appears
The torque specifications shown here are approximate
values obtained with a fully charged battery pack.
TORQUE SPECIFICATIONS
Clutch
Setting in-lbs
1-4
15-27
Small screws in softwood.
5-8
31-42
9-12
47-60
Medium screws in softwood
13-16
63-75
or small screws in hardwood.
NOTE: Because the settings shown in the table are
only a guide, use a piece of scrap material to test
the different clutch settings before driving screws
into the workpiece.
Mode Selector
Selector
button
AutoSTOP™ Indicator
Allow the tool to come to a complete stop before
changing modes. Press the selector button
cycle between the settings. When the tool is con-
nected to the ONE-KEY App™, the indicator will blink.
Select wireless
to change the default RPM, BPM,
and AutoSTOP™
KEY™ App on your smart device.
Selecting Speed
The speed selector is on top of the motor housing.
Allow the tool to come to a complete stop before
changing speeds. See "Applications" for recom-
mended speeds under various conditions.
1. For Low speed, push the speed selector to display
"1".
2. For High speed, push the speed selector to display
"2".
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
For forward (clockwise) rotation, push in the control
switch
from the right side of the tool. Check the
direction of rotation before use.
For reverse (counterclockwise) rotation, push in the
from the left side of the tool. Check
control switch
direction of rotation before use.
To lock the trigger, push the control switch to the
center position. The trigger will not work while the
control switch is in the center locked position. Always
lock the trigger or remove the battery pack before
performing maintenance, changing accessories,
storing the tool and any time the tool is not in use.
5
Applications
Modes
1, 2, 3
ONE-KEY™ Indicator
control settings via the ONE-
to
Publicidad
