Publicidad
Idiomas disponibles
Idiomas disponibles
To reduce the risk of injury, always
WARNING
hold or brace securely.
Starting, Stopping and Controlling Speed
1. To start the tool, grasp the handle(s) firmly and
pull the trigger.
NOTE: An LED is turned on when the trigger is
pulled and will go off shortly after the trigger is
released.
2. To vary the speed, increase or decrease the pres-
sure on the trigger. The further the trigger is pulled,
the greater the speed.
3. To stop the tool, release the trigger. Ensure the
tool has come to a complete stop before laying
the tool down.
Place the bit on the work surface and apply firm pres-
sure before starting. Too much pressure will slow the
bit and reduce drilling efficiency. Too little pressure
will cause the bit to slide over the work area and dull
the point of the bit.
If the tool begins to stall, reduce pressure slightly to
allow the bit to regain speed. If the bit binds, reverse
the motor to free the bit from the workpiece.
Overloading
Continuous overloading may cause permanent dam-
age to tool or battery pack.
APPLICATIONS
To reduce the risk of electric shock,
WARNING
check work area for hidden pipes
and wires before drilling or driving screws.
To reduce the risk of injury in applications that
produce a considerable amount of dust, use
an OSHA compliant dust extraction solution
in accordance with the solution's operating
instructions.
Drilling in Wood, Composition Materials and
Plastic
When drilling in wood, composition materials and
plastic, select the
Start the drill slowly, gradually increasing speed as
you drill. When drilling into wood, use wood augers
or twist drill bits. Always use sharp bits. When using
twist drill bits, pull the bit out of the hole frequently to
clear chips from the bit flutes. To reduce the chance of
splintering, back work with a piece of scrap wood. Se-
lect low speeds for plastics with a low melting point.
Drilling in Metal
When drilling in metal, select the
ing mode. Use high speed steel twist drills or hole
saws. Use a center punch to start the hole. Lubricate
drill bits with cutting oil when drilling in iron or steel.
Use a coolant when drilling in nonferrous metals such
as copper, brass or aluminum. Back the material
to prevent binding and distortion on breakthrough.
Drilling in Masonry
When drilling in masonry, select the
operating mode. Use high speed carbide-tipped bits.
Drilling soft masonry materials such as cinder block
requires little pressure. Hard materials like concrete
require more pressure. A smooth, even flow of dust
indicates the proper drilling rate. Do not let the bit
spin in the hole without cutting. Do not use water to
settle dust or to cool bit. Both actions will damage
the carbide.
Drilling
drill-only operating mode.
drill-only operat-
hammer drill
Driving Screws and Nut Running
Drill a pilot hole when driving screws into thick or hard
materials. Set the torque selector collar to the proper
position and set the speed to low. Use the proper
style and size screwdriver bit for the type of screw
you are using. With the screwdriver bit in the screw,
place the tip of the screw on the workpiece and apply
firm pressure before pulling the trigger. Screws can
be removed by reversing the motor.
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
ONE-KEY™
Chemical Burn Hazard.
WARNING
This device contains a
lithium button/coin cell battery. A new
or used battery can cause severe in-
ternal burns and lead to death in as
little as 2 hours if swallowed or enters the body.
Always secure the battery cover. If it does not
close securely, stop using the device, remove the
batteries, and keep it away from children. If you
think batteries may have been swallowed or
entered the body, seek immediate medical atten-
tion.
Internal Coin Cell Battery
An internal coin cell battery is used to facilitate full
ONE-KEY™ functionality.
To replace the coin cell battery:
1. Remove the battery pack.
2. Remove the screw(s) and open the coin cell bat-
tery door.
3. Remove the old coin cell battery, keep it away from
children, and dispose of it properly.
4. Insert the new coin cell battery (3V CR2032), with
the positive side facing up.
5. Close the battery door and tighten the screw(s)
securely.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
6
Publicidad
