EINHELL GE-PS 18/15 Li BL Manual De Instrucciones Original página 21

3. Proper use
This cordless branch chainsaw is designed for
for sawing trunks, branches, wooden beams and
boards etc., and for performing cross cuts and
longitudinal cuts. It is not suitable for cutting any
materials other than wood. This branch chainsaw
is not designed for tree-felling purposes.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Motor power supply: ............................... 18 V DC
Idle speed n : .............................. Level 3300 rpm
0
Cutter rail length ...................................... 158 mm
Max. cutting length: ................................ 125 mm
Cutting speed at rated rpm: ......................4.8 m/s
Weight ........................................... approx. 1.1 kg
Chain type ........ Hangzhou Jingfeng Tools: 28 DL
Cutter rail type: Hangzhou Jingfeng Tools: 153 mm
Danger!
Sound and vibration
Sound and vibration values were measured in ac-
cordance with EN 62841-1 and EN 62841-4-1.
L sound pressure level ..................... 76.2 dB(A)
pA
K uncertainty .......................................... 2.4 dB
pA
L sound power level ........................ 87.2 dB(A)
WA
K uncertainty .......................................... 2.4 dB
WA
L sound power level guaranteed ......... 90 dB(A)
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) were determined in accordance with EN
62841-1 and EN 62841-4-1.
Anl_GE-PS_18-15_Li_BL_Solo_SPK13.indb 21 Anl_GE-PS_18-15_Li_BL_Solo_SPK13.indb 21
GB
Handle under load
Vibration emission value front handle
a = 2.205 m/s
2
h
Vibration emission value rear handle
a = 2.205 m/s
2
h
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
5. Before starting the equipment
Warning!
Always remove the battery pack before making
adjustments to the equipment.
Danger! Do not fi t the battery until the chainsaw
has been fully assembled and the chain tension
has been set. Always wear protective gloves
when working on the chainsaw to protect yourself
against injury.
5.1 Fitting the cutter rail and saw chain
•
Carefully unpack all parts and check that they
are complete (Fig. 2-3).
•
Undo the fastening screw of the chain wheel
cover (9) (Fig. 4).
•
Take off the chain wheel cover (8) (Fig. 5).
- 21 -
2
03.05.2023 15:22:30 03.05.2023 15:22:30