Publicidad
Idiomas disponibles
Idiomas disponibles
Translation of the original instructions
MECANICAL SPECIFICATIONS
Dimensions (cm)
Weight (kg)
Protection rating
ELECTRICITY SUPPLY
- SPOT 3900 - 230 V / PRO 230 V / 2600 / 2700 : The material is supplied with a 16A plug type CEE7/7 and must only
be used on a single-phase electrical installation 230V (50-60 Hz) with 3 wires including one connected to earth.
- SPOT 3900 - 400 V / PRO 400 V : The material is supplied with a 16A plug type CEE7/7 and must only be used on a
two-phase electrical installation 400 V (50-60 Hz) with 3 wires including one connected to earth.
The permanent current absorbed (l1p or ILp) displayed in the section «technical specifications» of this manual relates
to use at maximum power. Check that the power supply and its protection (fuse and/or circuit breaker) are compatible
with the current needed by the machine. In some countries, it may be necessary to change the plug to allow the use
at maximum settings.
NB: If the product trips the circuit breaker, please check that the correct fuse and an adequate circuit
breaker are being used.
OPERATING AND SETTING (FIG III-PAGE 2)
A - SPOT 3900 - 230 V / 3900 - 400 V / PRO 230 V / PRO 400 V
•
Connect the machine to an approprate power supply
•
Connect the gun with its connector.
Nb: PRO 230 V and PRO 400 V have, in addition to the power connector, a connector to command the
torch trigger:
- Connect the latter if you wish to start by using the trigger.
- Disconnect it if you prefer using the generator with automatic start (see OPERATION section).
•
Press the « on/off » key (
•
The indicators switch on for few seconds then the machine displays:
- Tool
, n°1 by default, (star welding or dent pulling clamp).
1
-
, Power level, n°5 by default, (setting adapted for 0.8mm steel sheets).
2
•
To change the power level, press the + or – keys
automatically.
•
The available power levels allow the straightening of sheets of varying thickness (fig IV-
•
To change the tool used with the gun, press the tool selection key
The tool indicator will blink for 5 seconds. During this time, it is possible to change the tool number by pressing
the + or - keys (
Available Tools (fig. IV-
Straightening using the star hammer,
1
or dent pulling clamp.
2
Crimped welding wire or rings for straightening
3
Impact reduction with specific copper tip
4
Carbon electrode for tempering
B - SPOT 2600 / 2700
•
Connect the machine to an appropriate power supply,
•
To start the equipment, turn on the potentiometer. Put the potentiometer on «O» for standby mode (
•
Select the start mode using the potentiometer:
- Range 6 (left): star or ring welding for sheet stretching.
- Range 7 (top): corrugated wire welding, ideal for curved areas.
- Range 8 (right): Dent pulling work with the adapted copper tip.
•
To change the power level, rotate the potentiometer up to the required power.
14
SPOT 2600 / 2700 / 3900 - 230 V
3900 - 400 V / PRO 230 V/ PRO 400 V
20 x 32 x 18
).
6
).
3
)
B
22.5 x 36 x
23.5
17.8
22.7
. Keep the desired key pressed to scroll through the levels
3
4
.
5
Welding rivets for side rods
6
Welding rings for fixing vehicle body.
Welding studs for vehicle body and connecting
7
beams
22.5 x 36 x
22.5 x 36 x
23.5
23.5
23
25.5
IP 21
).
A
EN
22.5 x 36 x
23.5
25.5
).
6
Publicidad
