EINHELL PICOBELLA 18/215 Manual De Instrucciones Original página 22

The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
The machine noise might exceed 85 dB (A). The
operator will require noise protection measures if
this is the case.
Important!
The vibration value changes according to the
area of application of the electric equipment and
may exceed the specifi ed value in exceptional
circumstances.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
5. Before starting the equipment
The equipment is supplied without batteries
and without a charger.
5.1 Turn the steady grip out of the transport
position (Fig. 3-4)
Important! For transport reasons the steady grip
is turned 90° to the side. For you to be able to
work with the equipment, the steady grip must be
aligned in line with the brush housing (working
position).
1. Slacken the lock nut (8) by turning it counter-
clockwise and turn the steady grip as far as it
will go.
2. Secure the lock nut (8) by turning it clockwise.
5.2 Fitting the additional handle (Fig. 5)
Using the handle screws (6), fasten the additio-
nal handle (B) (the screws are accessible from
below) and the holder (C) at the area provided.
5.3 Adjusting the length of the long handle
(Fig. 6)
To ensure that you have a comfortable working
position, the length of the long handle can be
adjusted.
Anl_Picobella_18_215_SPK13.indb 22 Anl_Picobella_18_215_SPK13.indb 22
GB
1. Slacken the lock nut (8) by turning it counter-
clockwise.
2. To change the length of the long handle, pull
the long handle (9) out of the steady grip (D)
or push it into the steady grip.
3. Make sure that the steady grip is in the wor-
king position (section 5.1) and secure the
lock nut (8) by turning it clockwise.
5.4 Adjusting the additional handle (Fig. 5)
Undo the two fastening screws (6) on the additi-
onal handle until it can be moved in any direction
without any great resistance. Set the required
position and tighten the two fastening screws (6)
again.
5.5 Fitting the cleaning brushes (Fig. 7-10)
Remove the brush covers on the sides (Fig. 7 /
Item E, F). The product is supplied complete with
a 2-piece MEDIUM nylon brush (black). A nylon
brush (Fig. 2 / Item A) is equipped with a side
brush. The cleaning brushes have rubber caps
(Fig. 8 / Item G) on the outside. Slot the nylon
brush with side brush onto the brush mount (Fig.
9) on either the left or right side according to your
requirements and the other nylon brush onto the
other brush mount. Fit the brush covers back in
place. The wide brush cover (Fig. 7 / Item E) is
for the nylon brush with side brush. The MEDIUM
nylon brush is ready-fi tted (Fig. 10).
The SOFT nylon brush (yellow/green) (Fig. 10a)
and the ULTRA metal brush (Fig. 10b) must be fi t-
ted in the same way, but do not have a side brush.
They come supplied complete with a narrow
brush cover which must be used instead of the
wide brush cover.
Warning! There is a risk of injury from the bristles
of the metal brush – wear safety gloves.
5.6 Removing cleaning brushes
Remove the brush covers on the sides (Fig. 7 /
Item E, F). Press the middle of the rubber cap
(Fig. 11 / Item G) to actuate the release button un-
derneath and pull off the brush at the same time.
Warning! There is a risk of injury from the bristles
of the metal brush – wear safety gloves.
5.7 Water inlet connector (Fig. 12 – 14b)
To achieve top cleaning results quickly, we recom-
mend wet cleaning.
Important!
•
Observe the requirements of EN 1717 in rela-
tion to the connection of the water connection
- 22 -
10.05.2023 08:51:41 10.05.2023 08:51:41