EINHELL TC-SS 405 E Manual De Instrucciones Original página 13

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
1. Safety regulations
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Safety regulations
1. Important: Whenever you use electric tools it
is imperative to take basic safety precautions
in order to reduce the risk of fi re, electric
shock and personal injury. Essential safety
precautions include:
2. In an emergency, switch off the machine di-
rectly and pull out the power plug.
3. Follow all these instructions before and while
you are working with the saw.
4. Keep these instructions in a safe place.
5. Always pull out the power plug before adjus-
ting or servicing the machine.
6. Give these safety regulations to all persons
who work on the machine.
7. Do not use this saw to cut fi re wood.
8. Never use the saw to cross -cut round timber
unless it is equipped with a suitable holding
device.
9. The machine is equipped with a safety switch
to prevent it being switched on again acciden-
tally after a power failure.
10. Before you use the machine for the fi rst time,
check that the voltage marked on the rating
plate is the same as your mains voltage.
11. If you need to use an extension cable, make
sure its conductor cross-section is big
enough for the saw's power consumption. Mi-
nimum crosssection: 1 mm
12. If you use a cable reel, the complete cable
Anl_SA_TC_SS_405_E_SPK8.indb 13 Anl_SA_TC_SS_405_E_SPK8.indb 13
GB
13. Never carry the saw by its cable.
14. Check the power cable. Never use a faulty or
15. Do not use the cable to pull the plug out of the
16. Do not leave the saw in the rain and never
17. Provide good lighting.
18. Never saw near combustible liquids or gases.
19. Wear suitable work clothes! Never wear loose
20. Keep long hair in a hair net.
21. Avoid abnormal working postures.
22. Keep children away from the machine when it
23. Keep your workplace clean of wood scrap
24. Do not allow other persons, particularly
25. Persons working on the machine should not
26. After you have switched off the motor, never
27. Fit only blades which are well sharpened and
28. Faulty saw blades have to be replaced
29. Never use saw blades which do not comply
30. It is imperative to make sure that all the
31. Never dismantle the machine's safety devices
32. Damaged or faulty safety devices have to be
33. Never cut workpieces which are too small to
34. Never load the machine so much that it cuts
35. Always press the workpiece fi rmly against the
36. Never remove loose splinters, chips or jam-
37. To rectify faults or remove jammed pieces of
.
2
38. Conversions, adjustments, measurements
- 13 -
has to be pulled off the reel.
damaged power cable.
socket-outlet. Protect the cable from heat, oil
and sharp edges.
use it in damp or wet conditions.
garments or jewellery.
is connected to the power supply.
and any unnecessary objects.
children, to touch the tool or the power cable.
Keep them away from your workplace.
be distracted.
slow down the saw blade by applying pressu-
re to its side.
have no cracks or deformations.
immediately.
with the data specifi ed in this manual.
devices used to cover the saw blade are in
good working order.
or put them out of operation.
replaced immediately.
hold securely in your hand.
out.
work top.
med pieces of wood when the saw blade is
running.
wood, always switch off the machine fi rst. -
Pull out the power plug!
and cleaning jobs are to be performed only
15.02.2018 09:59:11 15.02.2018 09:59:11