RIDGID HD1200 Manual Del Usuario página 6

OPERATION
WARNING:
!
• Do not leave Vac running while unattended - you may fail to notice important signs indicating abnormal
operation such as loss of suction, debris/liquid exiting the exhaust, or abnormal motor noises.
Immediately stop using Vac if you notice these signs.
• Do not leave Vac plugged in when not in use.
• Do not continue running when float has cut off suction.
• Sparks inside the motor can ignite airborne flammables.
liquids or in areas with flammable gases, vapors, or explosive/airborne dust. Flammable liquids,
gases, and vapors include: lighter fluid, solvent-type cleaners, oil-based paints, gasoline, alcohol,
and aerosol sprays. Explosive dusts include: coal, magnesium, aluminum, grain, and gun powder.
• Do not vacuum up explosive dusts, flammable liquids, or hot ashes.
• Do not leave sawdust or rags with stain or polyurethane residue inside Vac. Empty drum after picking up
these potentially self-heating materials.
WARNING:
!
• Do not expose to rain or allow liquid to enter motor compartment. Store indoors.
• Do not handle plug, switch, or Vac with wet hands.
• Unplug Vac before servicing. If your Vac is not working as it should, has missing parts, has been
dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center or call
customer service.
• When using an extension cord, use only outdoor-rated cords that are in good condition. Do not allow the
connection to come into contact with liquid.
CAUTION:
!
Vac/Blower for extended time or in a noisy area.
VACUUMING DRY MATERIALS
1. The Filter must always be correctly installed to
avoid leaks and possible Vac damage.
2. To maintain peak performance when vacuuming
fine dust, clean the Drum and Filter regularly.
NOTE: Do not use a wet Filter when picking up dry
material. The Filter will quickly clog and be difficult to clean.
3. If the Filter is wet, you must allow it to dry
completely or replace it with a dry Filter before
using the Vac to pick up dry material.
VACUUMING LIQUIDS
1. Vacuuming up small amounts of liquid (less than
2" (5 cm) collected in Dust Drum) does not require
Filter removal.
2. When larger amounts of liquid are to be picked up,
remove all dry use only Paper Filter(s) and replace
with a RIDGID wet application Foam Filter. Do Not
remove the Filter Cage or Float. The Foam Filter is
specifically designed for high volume liquid pick up.
If the paper Filter is used and becomes saturated,
you may see "mist" coming from the Blowing Port.
3. When the Drum is "full" the Float will rise and cut
off airflow. The motor sound will rise in pitch and
its speed will increase indicating the Drum is "full".
Turn OFF the Vac and unplug the power cord before
emptying the Drum.
To reduce the risk of fire, explosion, or damage to Vac:
To reduce the risk of electric shock or injury:
To reduce the risk of hearing damage, wear ear protectors when using the
4. Following use of Vac for wet pick up, allow Filter to
IMPORTANT: To reduce the risk of damage to the Vac,
do not run Motor with Float in raised position.
EMPTYING THE DUST DRUM (Fig. 8)
1. Unplug Power Cord from power source.
2. The Vac comes equipped with a Drain for easy
3. Remove the Powerhead Assembly (A) by pulling
6
Do not operate Vac near flammable
dry completely to avoid mildew and Filter damage.
WARNING:
!
Do not operate without filter cage and float, as
they prevent liquid from entering the impeller and
damaging the motor.
WARNING:
!
To reduce the risk of injury from accidental
starting, unplug power cord before emptying the
drum.
emptying of liquids.
suitable drain or receptacle and remove the Drain
Cap (C).
outward at the top of the Two Latches.
Position the Vac near a