Publicidad
Idiomas disponibles
Idiomas disponibles
2A - SECONDARY air register
Under the door of the hearth (on the right) there is the secondary air register.
This register must be opened (and therefore the lever completely pushed), in detail, for the combustion of wood, so that unburnt
carbon can be subject to a post-combustion, increasing the yield and assuring the cleaning of the glass (see chapter NORMAL
OPERATION). It is possible to get the air SECONDARY directly from outside through a flexible tube (fireproof NOT furnished
Picture 11
Ref A).
The adjustment of the registers necessary to reach the rated calorific yield is the following one:
Hourly consumption in kg/h
2,3
C - FAN ELECTRIC THERMOCONTROLLER
UNIT OPERATION.
This electronic thermocontroller for packaged units manages ventilation air
flows. The unit is switched on or off by pressing and holding the 1 button.
During operation the display shows the set speed alternating with unit status,
led 9.
When the unit is off, the display also remains off.
The unit can be controlled MANUALLY or AUTOMATICALLY.
MANUAL mode
To access MANUAL mode, press the 2 button; when the 3 light comes on the
function is active. The 4-5 buttons are used to select one of the five fan speeds,
also active when the flue is cold.
The motor is started in automatic mode by a mechanical thermostat (the display
shows WAIT), which is activated when the temperature is at least 45°C (fixed
value, not modifiable). The 6 led indicates that the thermostat contact is closed.
AUTOMATIC mode
To access AUTOMATIC mode, press the 2 button; when the 7 light comes on the function is active. Use the 5 button to set the
speed. The 4-5 buttons are used to select one of the five fan speeds.
In automatic mode the COMFORT temperature can also be selected. Press the 4 button to access the COMFORT temperature
setting and then set the value using 4-5. This setting allows the user to reduce fan noise when the room temperature measured by
the probe inside the controller exceeds the comfort set point; the motor operates one speed lower (this mode has no effect in first
speed) and is signalled by the 8 led.
LANGUAGE menu.
Pressing and holding the 2 button accesses the LANGUAGE menu, where the display language can be changed using the 4-5
buttons (IT, EN, DE, FR). Pressing the 2 button briefly again accesses the DISPLAY menu, where the brightness can be adjusted
(between 10 and 150). Pressing the 2 button briefly another time accesses the DEGREES menu, where the temperature display
can be set as °C or °F.
BUZZER menu
Pressing the 2 button briefly a final time accesses the buzzer menu, where audible buzzer can be enabled or disabled.
REMOTE CONTROL OPERATION:
The electronic controller for packaged units can be managed by an IR remote control.
• The controller is switched on or off by pressing and holding the 11-12 buttons.
• To switch from MANUAL to AUTOMATIC on the IR remote control press the 13-14 buttons. The LED
corresponding to the operating mode comes on, manual 3 or automatic 7.
• In MANUAL mode only the buttons in the 11-13 group are enabled for selecting one of the five speeds.
• In AUTOMATIC mode, the buttons in the 12-14 group are enabled for selecting one of the five speeds,
as well as the buttons in the 11-13 group for changing the COMFORT set point.
The 10 LED comes on whenever a button is pressed on the remote control; if this does not happen, check
the batteries.
WARNING: the correct operation of the unit is assured only for the proper motor for which it has been
manufactured. Improper use relieves the manufacturer from each responsibility.
(Picture
8)
PRIMARY air
CLOSED
(Picture 1
SECONDARY air
Picture 8
1/4 OPEN
-
Picture
15).
5
6
7
7
8
ENgLIsH
TERTIARY AIR
PRE - ADJUSTED
3
7
9
8
A
2
4
5
A
1 2 3 4
O1
10
11
13
6
OK
1
12
14
23
Publicidad
