Publicidad
Idiomas disponibles
Idiomas disponibles
STARTING/STOPPING INSTRUCTIONS
WARNING:
Operate this unit only in a well-ventilated outdoor area.
Carbon monoxide exhaust fumes can be lethal in a confined area.
WARNING:
Avoid accidental starting. Make sure to be in the
starting position when pulling the starter rope (Fig. 12). To avoid
serious injury, the operator and unit must be in a stable position
while starting.
NOTE:
This unit uses the Incredi-Pull™ starting system, which
significantly reduces the effort required to start the engine. There is
no harsh resistance when pulling the starter rope. Be aware that
this starting method is vastly different from (and much easier than)
previous starting techniques.
STARTING INSTRUCTIONS
1.
Check the oil level in the
crankcase. Refer to Checking
the Oil Level.
2.
Fill the fuel tank with fresh,
clean unleaded gasoline.
Refer to Fueling the Unit.
NOTE:
There is no need to turn
the unit on. The On/Off
Control is in the ON (I)
position at all times
(Fig. 10).
IF COLD... In cold weather
conditions (below 40°F),
push the red cold weather
start lever (Fig. 11) down
to the closed position and
continue to step 3. DO
NOT push this lever down
if the temperature is above
40°F.
NOTE:
DO NOT squeeze the
throttle control until step 8.
3.
Fully press and release the
primer bulb 10 times, slowly.
Some amount of fuel should
be visible in the primer bulb
(Fig. 11). If fuel cannot be
seen in the bulb, press and
release the bulb until fuel is
visible.
4.
Stand in the starting position
(Fig. 12).
5.
Pull the starter rope in a
controlled motion until the
unit starts.
IF COLD... In cold weather
conditions (below 40°F),
pull the red cold weather
start lever back up to the
open position after the unit starts.
6.
Wait 60 seconds.
7.
Tip the unit back so the blade does not touch the ground.
8.
Squeeze the throttle control and allow the engine to warm up for 30 to
60 seconds. The unit may be used during this time.
IF...
The engine does not start, go back to step 3.
IF...
The engine stops while squeezing the throttle, go back to step 4.
STOPPING INSTRUCTIONS
1.
Release the throttle control and allow the engine to cool down by idling.
2.
Press and hold the On/Off Control in the OFF (O) position until the unit
comes to a complete stop. (Fig. 10)
Throttle
Control
On/Off
Control
Fig. 10
Red Cold Weather
Starter Lever
Primer
Bulb
Fig. 11
Starting
Position
Starter
Rope
Fig. 12
STARTING/STOPPING INSTRUCTIONS
IF USING THE OPTIONAL PLUG-IN POWER START OR POWER BIT
START ACCESSORY
HOW TO START THE UNIT USING THE PLUG-IN POWER START OR
POWER BIT START ACCESSORY
NOTE:
This unit can use a Plug-In Power Start or Power Bit Start
optional accessory!
Please refer to the Plug-In Power Start or Power Bit Start operator's
manual for proper use of this feature. (Plug-In Power Start sold
separately / Power Bit Start included. Please refer to page 9 of this
manual for more information about these accessories.)
STARTING INSTRUCTIONS
1.
Check the oil level in the crankcase. Refer to Checking the Oil Level.
2.
Fill the fuel tank with fresh, clean unleaded gasoline. Refer to Fueling the Unit.
NOTE:
There is no need to turn the unit on. The On/Off Control is in the
ON (I) position at all times (Fig. 10).
IF COLD... For cold weather conditions (below 40°F), push the red cold weather
start lever (Fig. 11) down to the closed position and continue to step 3.
DO NOT push this lever down if the temperature is above 40°F.
NOTE:
DO NOT squeeze the throttle control until step 9.
3.
Fully press and release the primer bulb 10 times, slowly. Some amount
of fuel should be visible in the primer bulb (Fig. 11). If fuel can not be
seen in the bulb, press and release the bulb until fuel is visible.
4.
Place the Plug-In Power Start or Power Bit Start into the back of the
unit. Refer to the Operation section of the Plug-In Power Start or Power
Bit Start operator's manual.
5.
Press and hold the ON (I) button of the Plug-in Power Start or Power Bit
Start equipped drill in intervals no longer than 2 seconds each until the
unit starts.
IF COLD... For cold weather conditions (below 40°F), pull the red cold
weather start lever back up to the open position after the unit starts.
6.
Remove the Plug-In Power Start or drill from the unit.
7.
Wait 60 seconds.
8.
Stand in the starting position (Fig. 12). Tip the unit back so the blade
does not touch the ground.
9.
Squeeze the throttle control and allow the engine to warm up for 30 to
60 seconds. The unit may be used during this time.
IF...
The engine does not start, go back to step 3.
IF...
The engine stops while squeezing the throttle, go back to step 4.
STOPPING INSTRUCTIONS
1.
Release the throttle control and allow the engine to cool down by idling.
2.
Press and hold the On/Off Control in the OFF (O) position until the unit
comes to a complete stop. (Fig. 10)
OPERATING INSTRUCTIONS
HOLDING THE UNIT
WARNING:
Always wear eye, hearing, foot and body protection
to reduce the risk of injury when operating this unit.
Before operating the unit, stand in the
operating position (Fig. 13). Check for the
following:
• The operator is wearing eye protection and
proper clothing.
• Both hands are holding the handle bar firmly.
• The edger wheel adjusted for proper cut
depth as shown in Figure 14 and edger
positioned as shown in Figure 13.
ADJUSTING EDGER CUTTING DEPTH
1.
Gently pull the depth adjustment lever
away from the wheel bracket (Fig 14).
2.
To raise the cutting blade,
move the lever toward the
front of the wheel bracket
(Fig. 14). Lowering the wheel
decreases the cutting depth.
3.
To lower the cutting blade,
move the lever toward the
rear of the wheel bracket.
Raising the wheel increases
the cutting depth.
6
Fig. 13
Depth
Adjustment
Lever
Wheel
Bracket
Fig. 14
Publicidad
