Descargar Imprimir esta página

GRAPHITE 59G474 Manual Del Usuario página 10

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 58
Warning: Never perform any assembly or adjustment operations with
power connected to the mower. Always ensure that the power button is
in the off position and that the power plug is disconnected from the
extension cord.
Cleaning:
Do not spray water on the unit. Water ingress may damage components
such as the switch/plug and the electric motor.
Clean the unit with a cloth, hand brush, etc.
Consultation with Service is required:
(a) If the mower strikes an object.
(b) If the engine stops suddenly
c) If the blade is bent (do not align!)
d) If the motor shaft is bent (do not align!)
It is recommended that the mower blade be replaced at the end of the
mowing season. Always have the mower blade replaced by an
authorized service center (requires blade balance measurement).
An unbalanced blade causes violent vibration of the mower and
a risk of accident!
Checking the grass catcher box and any damaged parts
Check the grass tank for signs of wear at more frequent intervals.
Replace any worn or damaged parts.
Use only original spare parts for maintenance.
The component subject to the heaviest wear is the blade. Check the
condition of the blade and its holder at regular intervals. When the blade
is worn, replace it. If there is excessive vibration of the mower, it is a sign
of improper blade balance or deformation due to impact. In this case,
replace the blade.
Storing the mower:
Disconnect the power cord.
Allow the engine to cool for about 30 minutes.
Check, repair, or replace any power cord that shows signs of wear or
damage.
Tighten or replace worn, loose or damaged parts, and clean them
thoroughly.
Clean the outside of the unit thoroughly with a soft brush and cloth.
Do not use water, solvents or polishes. Remove all grass and debris,
especially from the vents.
Turn the unit on its side and clean the blade and blade guard. If grass
blades are on or near the blade, remove them with a wooden or plastic
tool to protect the blade.
To protect your mower from rust, wipe all exposed metal parts with an
oil-soaked cloth or spray with a light grease.
Keep the mower and extension cord in a locked, dry place out of the
reach of children to prevent unauthorized use or damage.
Cover loosely with a tarp for extra protection.
If transporting, be sure to properly secure the unit to the vehicle.
To reduce the storage space of the mower, the upper handle can be
folded as shown in Figure B.
Note: Do not pinch the electrical cord when folding the handle. Make
sure it does not get stuck or entangled when folding or unfolding the top
handle.
PROBLEM SOLVING
Always pull the mains plug and wait for the blade to stop
before carrying out any maintenance or cleaning work.
Symptom
Possible problem
Power off
Power socket damaged
Damaged extension cord Check, replace if damaged.
The grass is too high
The device is
not working
Safety / overload
protection has been
activated
Damaged extension cord Check, replace if damaged
The mower
The grass bin is full.
works
The mower's internal
intermittently
wiring is damaged
Cutting height too low
Solution
Turn on the power
Use a working power outlet
Increase the cutting height
Allow to cool for a few
minutes and increase the
cutting height
Do not operate the switch
lever at this time as it will
extend the safety safety
reset time
Empty the grass collector.
contact service
Increase the cutting height
The cutter blade tears the
grass or does not cut
The mower is
Machine underside badly
not working
clogged
properly
Blade mounted upside
down
The cutter
Cutting blade blocked
blade does not
rotate
Blade nut / bolt loose.
Blade nut / bolt loose
Excessive
vibration /
Cutting blade damaged
noise
TECHNICAL SPECIFICATIONS
Electric mower 59G474
Parameter
Supply voltage
Power frequency
Rated power
Spindle speed no load
Degree of protection
Mowing diameter
Mowing height range
Grass catcher capacity
Protection class
Mass
Year of production
59G474 indicates both the type and the machine designation
NOISE AND VIBRATION DATA
Sound pressure level
Sound power level
Vibration acceleration values
Information on noise and vibration
The noise level emitted by the equipment is described by: the emitted
sound pressure level LpA and the sound power level LwA (where K
denotes measurement uncertainty). The vibrations emitted by the
equipment are described by the vibration acceleration value ah (where K
is the measurement uncertainty).
The sound pressure level LpA, the sound power level LwA and the
vibration acceleration value ah specified in these instructions were
measured in accordance with EN 60335-2-77.
The vibration level indicated is representative of the basic use of the device
only. If the machine is used for other applications or with other working
tools, the vibration level may change. A higher vibration level will be
caused by insufficient or infrequent maintenance of the machine. The
reasons given above may result in an increased vibration exposure during
the entire service life.
In order to accurately estimate vibration exposure, it is necessary to
take into account periods when the unit is switched off or when it is
switched on but not used for work. When all factors are accurately
estimated, the total vibration exposure may be much lower.
In order to protect the user from the effects of vibrations, additional safety
measures should be implemented, such as: cyclical maintenance of the
device and working tools, securing proper hand temperature and proper
work organization.
ENVIRONMENTAL PROTECTION
Electrically powered products should not be disposed
of with household waste, but recycled at an
appropriate disposal facility. Please consult your
product dealer or local authority for disposal
information. Waste electrical and electronic equipment
contains substances that are not harmful to the
environment. Equipment which is not recycled poses
a potential hazard to the environment and human
health.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka
komandytowa with headquarters in Warsaw, ul. Pograniczna 2/4
(hereinafter: "Grupa Topex") informs that all copyrights to the content of
this manual (hereinafter: "Manual"), including among others. Its text,
photographs, diagrams, drawings, as well as its composition, belong
exclusively to Grupa Topex and are subject to legal protection under the
Act of 4 February 1994 on Copyright and Related Rights (ie Journal of
10
Replace the blade
Clean the device
Fix the blade in the correct
position
Serious damage, contact
the service center
Tighten the blade nut / bolt
Tighten the blade nut / bolt
Replace the blade
Value
230 V AC
50 Hz
1500 W
3500 min-1
IPX4
360 mm
20/35/50 mm
35 l
II
11 kg
LpA= 82,6 dB(A) K= 3 dB(A)
LwA= 94,4 dB(A) K= 1,89 dB(A)
ah= 3,44 m/s2 K= 1,5 m/s2

Publicidad

loading