Descargar Imprimir esta página

GRAPHITE 59G474 Manual Del Usuario página 9

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 58
and follow the instructions in the operating manual. Cut the grass in even
strips. The mower can be pushed or pulled. The mower is designed for
amateur use only.
Do not misuse the device.
DESCRIPTION OF THE GRAPHICAL PAGES FIG. A
The following numbering refers to the device components shown on the
graphic pages of this manual.
1.
Top guide handle
2.
Switch lever
3.
Safety button
4.
Electrical cable holder
5.
Power cord
6.
Grass tank
7.
Electrical cable clips
8.
Guide bar clamp knob
9.
Rear wheel
10. Front wheel
11. Grass outlet cover
12. Bottom guide
13. Grass container handle
14. Grass tank level indicator
15. Guide bar clamp knob
16. Top guide handle
* There may be differences between the drawing and the product.
DESCRIPTION OF THE GRAPHIC SYMBOLS USED
NOTE
WARNING
EQUIPMENT AND ACCESSORIES FIG. B
1.
Mower with guides
2.
Grass catcher
3.
Guide bar clamp knob
4.
Clips for attaching the cable
5.
Grass catcher handle
GETTING READY
Mounting the slide
Adjust the bottom guide
• Raise the lower handlebar to the desired position fig. C1 and then
secure it in place with the guide bar clamping knob
• Release the lock knob (1) fig. B and rotate the lower handlebar (2)
to the correct position and then lock the knob to secure the lower
handlebar in place. Assemble the upper guide to the lower guide with
the knob and guide lock washer (Fig. C)
Grass container installation
Assemble the holder: Place the top of the tank on a flat surface,
insert the tabs of the holder into the holes, and then press the holder
down to lock it in place. Fig.D1
Then install the lower mesh part, place it into the slot in the upper
rigid tank part make sure the rim is locked by the latches.
Next, press the bottom (mesh) part of the tank onto the metal clamp
using the clamps on the mesh.
To place the grass catcher on the mower, lift the grass ejection
guard off the mower and place the catcher on the tabs located on
the metal bracket (b) of the mower (a) fig. D2. A properly installed
hopper is shown in fig. D3
Connecting the power supply
The mains voltage must be as specified on the rating plate (230-240V).
The current protection of the mains must be min. 10A
Secure the power cord of the mower as shown in figure E1
Insert the plug of the mower into the connection socket of the
extension cable fig. E2. Secure the extension cable against dropping
and disconnecting in the holder below the switch fig. E2
OPERATION / SETTINGS
WARNING!
- Do not switch on the appliance until it is fully assembled. Always check
the extension cord for signs of damage before turning on the unit, only use
an undamaged extension cord.
Caution: A damaged extension cord can be very dangerous! Danger to life
and health of the user
- When attempting to run the mower in tall grass, the engine may
overheat and become damaged.
Switching on the mower:
To start the mower, press and hold the safety button (3) as shown in
1.
figure E3, pull the switch lever (2). towards the handlebar. After
following the steps in the sequence shown previously, the mower will
start.
2.
To turn off the mower, release the switch lever (2).
Note: It is not necessary to press or hold the safety button (3) after
the device has been started.
Setting the mowing height
Warning! Turn off the mower by releasing the switch lever and wait for
the motor and blade to stop before adjusting the cutting height, blades
continue to rotate for several seconds after the machine is turned off, a
rotating blade can cause injury.
For the first cut of the season or after a long time since the last mowing,
select a high cut adjustment.
Tips: For long grass, start mowing with the highest setting and then
gradually reduce the cutting height.
When and how to set up and take down a grass catch basin
Attach the grass catcher before operating the mower, see above for details
on grass catcher installation. When the mower is running, a blast of air
from the spinning blade will push out the grass indicator flap fig G1. When
the grass catcher is full, the indicator flap will rest flat fig. G2
Switching off the grass box
Note: Empty the tank when it is full to avoid blocking the exhaust port and
unnecessarily overloading the engine.
Disconnect the grass hopper by doing the following:
1.
Lift the rear grass outlet guard that is on top of the grass tank,
2.
Lift the grass hopper up to detach it from the mower body.
3.
Lower the rear grass outlet guard down.
Note: When mowing, safely place the extension cord on a sidewalk, path
or areas that have already been mowed.
WARNING!
When the engine is turned off, the blade continues to spin for a few
seconds, so do not touch the underside of the mower until the
blade stops!
Warning! When mowing, do not let the engine run under overload.
When an engine overload occurs, the engine speed slows down and you
will hear a change in engine sound, when this happens, stop mowing,
release the switch lever and raise the cutting height. Failure can cause
damage to the machine.
Select a cutting height that is suitable for the desired grass height. If
necessary, mow in several passes so that the maximum grass cutting
height per pass is 4 cm.
When mowing, make sure you avoid areas that could impede the free
movement of the extension cord.
Blade
Always disconnect the mower before checking the blade in any way. After
stopping the engine, remember that the blade will continue to run for a few
seconds before it stops. Never try to stop the blade. Check at regular
intervals that the blade is properly attached, is in good condition, and is
sharpened properly. Replace it if necessary.
If the rotating blade strikes any object, stop the mower and wait until the
blade comes to a complete stop. Then check the condition of the blade
and the blade holder. Replace the blade immediately if it has been
damaged.
OPERATION AND MAINTENANCE
Warning! Stop the mower and unplug the power adapter before
removing the grass catcher.
Always pull the mains plug before carrying out any maintenance or
cleaning work!
Note: To ensure long and reliable service, perform the following
maintenance regularly:
Check for obvious defects such as a loose, dislodged or damaged
blade, loose attachments and worn or damaged mower
components.
Check that the covers and guards are undamaged and properly
attached to the mower.
Perform necessary maintenance/inspection or repairs before
operating the mower.
Warning: Remember to contact a professional maintenance agency
when replacing the blade.
9

Publicidad

loading