IMG STAGELINE LSX-049SG Manual De Instrucciones página 9

2. a defect might have occurred after a drop or
similar accident,
3. malfunctions occur.
The unit must in any case be repaired by skilled
personnel.
G
Never pull the mains cable to disconnect the
mains plug from the mains socket, always seize
the plug.
G
For cleaning the housing only use a dry, soft
cloth, never use water or chemicals.
G
No guarantee claims for the unit and no liability
for any resulting personal damage or material
damage will be accepted if the unit is used for
other purposes than originally intended, if it is not
correctly installed or connected or operated, or
not repaired in an expert way.
If the unit is to be put out of operation
definitively, take it to a local recycling plant
for a disposal which is not harmful to the
environment.
G
Important for U. K. Customers!
The wires in this mains lead are coloured in
accord ance with the following code:
green/yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead of
this appliance may not correspond with the
coloured markings identifying the terminals in
your plug, proceed as follows:
1. The wire which is coloured green and yellow
must be connected to the terminal in the plug
which is marked with the letter E or by the earth
symbol , or coloured green or green and yel-
low.
2. The wire which is coloured blue must be con-
nected to the terminal which is marked with the
letter N or coloured black.
3. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
Warning – This appliance must be earthed.
3 Applications
The laser effect unit is capable of projecting different
shapes and geometric patterns onto a surface or into
an artificial fog either independently (also by music
control via the internal microphone) or by a DMX
control. It can be used e. g. on stage or in discothe-
ques. For operation via a DMX controller, nine DMX
channels are available. An overview of the DMX con-
trol possibilities can be found in chapter 8.1.
4 Mounting and Setting into Operation
The laser must safely be mounted in an expert way.
The person who sets up the unit together with all
additional components (e. g. mirror, lenses, projec-
tion area) to create a laser system, becomes the
legitimate manufacturer of this system. Observe in
any case the warning notes in chapter 2.1.
WARNING 1. According to international safety
regulations the laser must be
installed so that the laser beam
has a minimum distance of 3 m to
the floor when persons stand or sit
under the beam (fig. 2). However the unit can
also be installed so that in the horizontal plane
the laser beam keeps a minimum distance of
2.5 m to persons (fig. 3).
2. As the safety regulations are different in each
country, the regulations of the country where
the unit will be operated must be observed in
any case!
3. Select the mounting location so that a sufficient
air circulation will be ensured during operation.
The unit must have a minimum distance of
50 cm to adjoining surfaces and the air vents at
the housing must not be covered in any case.
4. If the laser is installed at a place where people
may stand or sit under, it must additionally be
secured (e. g. by a safety rope at the mounting
bracket; fix the safety rope so that the maxi-
mum falling distance of the unit does not
exceed 20 cm).
1) Tightly screw the laser with its mounting bracket
(3) to a suitable place, e. g. with a stable mount-
ing screw or a support for lighting units (C hook)
at a cross bar.
2) To align the unit, release the two locking screws
(1) at the mounting bracket. Adjust the desired
inclination of the unit and retighten the screws.
3) Connect the supplied mains cable to the mains
jack (5) first and then to a socket (230 V~ / 50 Hz).
Thus, the unit is switched on.
For a more convenient operation it is recom-
mended to connect the unit to a socket which
can be switched on and off via a light switch.
4) To switch on the laser beam, insert the supplied
key into the lock of the switch KEY LOCK (7) and
turn the key clockwise.
IMPORTANT! The laser system must not be
operated without the presence of a laser pro-
tection adviser. In case of absence, this adviser
should have secured the laser beam with the
key switch against unauthorized operation.
GB
9