DeWalt DW742 Manual Del Usuario página 34

E N G L I S H
Connecting - saw bench position
• Replace the saw blade guard by the guard supplied with the dust
extraction kit and connect the hose from the under-table guard to it.
• Proceed as for mitre saw position.
Mitre saw extra support/length stop (fig. A4)
The extra support and length stop can be mounted on the left-hand side
or on the right-hand side, or with two sets on either side.
• Fit the items 34 - 41 onto the two guide rails (35).
• Use the inclinable support (36) for cross-cutting 210 mm wide boards
(15 mm thick).
Roller support table (fig. A5)
In mitre saw mode, the roller support table can be mounted on the left-hand
side or on the right-hand side, or with two sets on either side. In saw bench
mode, it can also be mounted in front or at the rear of the saw table.
Side extension table (fig. A6)
The side extension table increases the distance from the rip fence to the
blade to 600 mm or more, depending on the rod length fitted to the
machine and the clamped position of the table.
The side extension table must be used in conjunction with guide rails (35)
(option). The adjustable table is equipped with an engraved scale along its
front edge and mounted on a sturdy base which clamps to the guide rods.
• Fit the extension table to the right-hand side of the machine for
continuity of the distance scale on both tables.
Single sliding table (fig. A7)
This sliding table (44) allows for board sizes to the left of the blade up to
1200 x 900 mm.
The guide rods are mounted on a sturdy alloy extrusion which is quickly
detachable from the machine and yet fully adjustable is all planes.
The fence incorporates a full length measuring tape for quick positioning of
an adjustable stop and an adjustable support for narrow workpieces.
Transporting
Always transport your saw in saw bench mode with the upper blade guard
fitted. Remove the legs.
Maintenance
Your D WALT machine has been designed to operate over a long period
E
of time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Lubrication
The bearings of the motor are pre-lubricated and watertight.
• Slightly oil the rotating table bearing surface where it slides on the lip of
the fixed table at regular intervals.
• Clean the parts subject to accumulation of sawdust and chips
periodically with a dry brush.
Unwanted tools and the environment
Take your tool to an authorized D
disposed of in an environmentally safe way.
en - 8
WALT repair agent where it will be
E
GUARANTEE
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfied with the performance of your
D WALT machine, simply return it within 30 days, complete as
E
purchased, to the point of purchase, for a full refund or exchange.
Proof of purchase must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your D
12 months following purchase, it will be undertaken free of charge at
an authorized D WALT repair agent. Proof of purchase must be
E
produced. Includes labour and spare parts for Power Tools. Excludes
accessories.
• ONE YEAR WARRANTY •
If your D WALT product becomes defective due to faulty materials or
E
workmanship within 12 months from the date of purchase,
we guarantee to replace all defective parts free of charge or, at our
discretion, replace the unit free of charge provided that:
• The product has not been misused.
• Repairs have not been attempted by unauthorized persons.
• Proof of purchase date is produced.
This guarantee is offered as an extra benefit and is additional to
consumers statutory rights.
For the location of your nearest authorized D
please use the appropriate telephone number on the back of this
manual. Alternatively, a list of authorized D
details on our after-sales service are available on the Internet at
www.2helpu.com.
WALT machine, in the
E
WALT repair agent,
E
WALT repair agents and full
E
25