Publicidad
Idiomas disponibles
Idiomas disponibles
Locking/Unlocking the Lever Arm
The lever arm should be locked any time the tool is
being transported or is not in use.
To lock the lever arm, push back on the lever arm
collar (1) and lower the lever arm (2) push the carry
hook up to secure the lever arm (3).
1
To unlock, remove lever arm from carry hook (1). Push
back on lever arm collar (fully compress the spring)
(2). Pull up on lever arm (3) collar will click into place.
2
ONE-KEY™
To learn more about the ONE-KEY™ functionality for
this tool, please refer to the quick reference included with
this product or go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store or
Google Play from your smart device.
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
Always remove battery pack before
WARNING
changing or removing accessories.
Only use accessories specifically recommended
for this tool. Others may be hazardous.
To reduce the risk of short circuit, when setting tool
or battery down, do not allow battery to contact
corrosive or conductive fluid.
To reduce the risk of injury, wear safety goggles
or glasses with side shields. Always wear leather
gloves over latex/rubber gloves to avoid entangle-
ment. Cable tip may be sharp.
2
3
3
1
Using the Forward/Off/Reverse Switch
The forward/off/reverse switch controls the rotation
of the cable.
1. For forward (clockwise) rotation, turn the forward/
off/reverse switch to the arrow pointing away from
the wheels of the tool
rotation before use.
2. For reverse (counterclockwise) rotation, turn the
forward/off/reverse switch to the arrow pointing
towards the wheels of the tool
direction of rotation before use.
3. To lock the switch, turn the forward/off/reverse
switch to the center position O. The cable will not
spin while the forward/off/reverse switch is in the
center locked position. Always lock the switch or
remove the battery pack before performing mainte-
nance, transporting the tool, changing accessories,
storing the tool and any time the tool is not in use.
Inserting Cable Into Drain
1. Place the tool at a distance no greater than two feet
from the drain opening. If needed, place protective
covers in the work area.
2. Pull cable out of its carrier and into the rear guide
hose connection using the guide tube. WARNING!
Always wear leather gloves over latex/rubber gloves
to avoid entanglement. Route the cable directly into
the drain from the tool, minimizing exposed cable
and changes in direction.
3. Continue feeding the cable until approximately
one foot of cable remains before the guide tube.
4. Disconnect the cable from its carrier. WARNING!
Rotating cable while still connected to their carriers
may cause striking or crushing injuries.
5. Turn the forward/off/reverse switch to the forward
position
to rotate the cable.
6. If needed, attach additional sectional cables ac-
cording to the instructions under "Connecting/
Disconnecting Sectional Cables".
7. Continue feeding cable into the drain until the
obstruction is reached. Cable can be fed manually
or by advancing the CABLE-DRIVE™ system.
8. When the clog is reached, move the cable in a back
and forth motion until the obstruction is cleared.
Using the Cable-Drive™
The cable feed system controls the advancement
and retraction of the cable.
1. To feed the cable, make sure the forward/off/
reverse switch is in forward
outward and turn it to the feed/retract setting
Check the direction of movement before use.
2. To retract the cable, make sure the forward/off/
reverse switch is in reverse
lar outward and turn it to the feed/retract setting
. Check the direction of movement before use.
Using Manual Operation
To feed the cable:
1. Pull the feed collar outward and rotate to Spin O.
2. Grasp the cable close to the front collar and pull
enough cable from the machine to start cable
in the drain opening. WARNING! Always wear
leather gloves over latex/rubber gloves to avoid
entanglement.
3. Turn forward/off/reverse switch to forward
4. Pull 6-8" of cable from the tool.
5. Press down on lever arm with one hand while
guiding the cable down the line with the other.
6. Release lever arm.
7. Repeat steps 2-6 until obstruction is reached.
5
. Check the direction of
. Check the
. Pull the feed collar
. Pull the feed col-
.
.
Publicidad
