Milwaukee 6176-20 Manual Del Operador página 3

Sierra tronzadora abrasiva de 35,6 cm, heavy duty
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

28. Use proper accessories. Consult this manual for recommended
accessories. Using improper accessories may be hazardous. Be
sure accessories are properly installed and maintained. Do not de-
feat a guard or other safety device when installing an accessory or
attachment.
29. Maintain tools carefully. Keep handles dry, clean and free from
oil and grease. Keep cutting edges sharp and clean. Follow instruc-
tions for lubricating and changing accessories. Periodically inspect
tool cords and extension cords for damage. Have damaged parts
repaired or replaced by a MILWAUKEE service facility.
30. Maintain labels & nameplates. These carry important informa-
tion. If unreadable or missing, contact a MILWAUKEE service facil-
ity for a free replacement.
WARNING! Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
lead from lead-based paint
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
Wheel Instructions
1.
Use only the edge (not the sides) of the wheel for cutting. Do not
allow the wheel to twist or bind.
2.
Keep hands and body away from the rotating wheel. Do not wear
loose clothing when using this tool.
3.
Store cut-off wheels with care. Do not drop them or subject them to
excessive heat, cold or humidity.
4.
Make sure that all wheel flanges and other mounting hardware are
in good condition and are always used properly. Defective or miss-
ing parts may cause damage to the wheel. Always use mounting
flanges supplied with the tool.
5.
Cutting with a damaged wheel is very hazardous. After installing a
new wheel, leave the tool unplugged and rotate the wheel by hand
to see if it is uneven, warped, or cracked. If so, discard the wheel
and replace it with a new one. Do not use a wheel that has been
dropped; impact may result in breakage.
6.
Before starting a cut, step back from the tool and make a trial run to
confirm that the wheel is in good condition. Trial run periods are:
When replacing a cut-off wheel — over 3 minutes.
When starting routine work — over 1 minute.
7.
Never try to remove or clamp the workpiece to the tool while the cut-
off wheel is rotating.
8.
Before installing a cut-off wheel, always inspect it for cracks. Visu-
ally check resinoid and rubber-bonded wheels for cracks. Replace
cracked wheel immediately.
9.
Always check maximum operating speed established for wheel
against machine speed. Do not exceed the maximum operating speed
that is marked on the wheel.
SPECIAL SAFETY INSTRUCTIONS - ABRASIVE CUT-OFF MACHINES
To reduce the risk of injury, avoid inhalation of dust generated
by grinding and cutting operations. Exposure to dust may
cause respiratory ailments. Use approved NIOSH or OSHA
respirators, safety glasses or face shields, gloves and pro-
tective clothing. Provide adequate ventilation to eliminate
dust, or to maintain dust level below the Threshold Limit
Value for nuisance dust as classified by OSHA.
31. Tool service must be performed only by qualified repair
personnel. Service or maintenance performed by unqualified per-
sonnel may result in a risk of injury.
32. When servicing a tool, use only identical replacement parts.
follow instructions in the maintenance section of this
manual. Use of unauthorized parts or failure to follow maintenance
instructions may create a risk of shock or injury.
WARNING!
10. Do not force a wheel onto the machine or alter the size of the arbor
hole. Don't use a wheel that fits the arbor too loosely. If the wheel
doesn't fit the machine, get one that does.
11. Do not attempt to install saw blades on this tool because it is not
designed for this type of blade.
12. Do not overtighten wheel nut.
Machine Instructions
1.
Start cutting only after the motor has reached full speed.
2.
Release switch immediately if the cut-off wheel stops rotating or if
the motor sounds like it is straining.
3.
Keep flammable and fragile objects away from this tool. Do not allow
cut-off sparks to contact the operator's hands, face or feet.
4.
Place the tool securely on a flat, level surface.
5.
Always use the tool with the proper voltage specified on the tool's
nameplate.
6.
Never touch a short cut-off piece until it cools.
7.
Never attempt to cut material larger than the rated capacity listed in
"Specifications".
8.
Never stand in line with the wheel while cutting. Always stand to the
side.
9.
Always keep guards in place.
10. Always start the cut gently. Do not bump or bang a wheel to start a
cut.
11. Never make any freehand cuts. Always place the workpiece be-
tween the vise and fence when making cuts.
SERVICE
page 3

Publicidad

Tabla de contenido
loading

Tabla de contenido