Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
ENGLISH
Getting Started
Getting Started
Introduction
Introduction
This manual provides operation instructions and information required to
operate the Hunter Revolution
Tire Changer. Read and become familiar with
™
the contents of this manual prior to operating the Hunter Revolution
Changer.
The owner of the Hunter Revolution
for arranging technical training. The Hunter Revolution
be operated only by qualified trained technicians. Maintaining records of
personnel trained is solely the responsibility of the owner and management.
This manual assumes the technician has already been trained in basic tire
changing procedures.
For Your Safety
For Your Safety
Hazard Definitions
Watch for these symbols:
Hazards or unsafe practices, which could result in minor
personal injury or product or property damage.
Hazards or unsafe practices, which could result in severe
personal injury or death.
Immediate hazards, which will result in severe personal
injury or death.
These symbols identify situations that could be detrimental to your safety and/
or cause equipment damage.
In addition, notes will appear as:
Information pertaining to a specific step, procedure or feature.
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before operating the The Hunter Revolution
Changer. Read and follow the instructions and warnings provided in the
service, operation and specification documents of the products with which this
The Hunter Revolution
Tire Changer is used (i.e., automobile manufacturers,
™
tire manufacturers etc.).
Do not operate equipment with a damaged cord or equipment that has been
dropped or damaged until a Hunter Service Representative has examined it.
Always unplug equipment from electrical outlet when not in use. Never use the
cord to pull the plug from the outlet. Grasp plug, twist and pull to disconnect.
If an extension cord is necessary, a cord with a current rating equal to or more
than that of the equipment should be used. Cords rated for less current than
the equipment may overheat. Care should be taken to arrange the cord so
that it will not be tripped over or pulled.
Verify that the electrical supply circuit and the receptacle are properly
grounded.
To reduce the risk of electrical shock, do not use on wet surfaces
or expose to rain.
Verify the appropriate electrical supply circuit is the same voltage and
amperage ratings as marked on the tire changer before operating.
DO NOT ALTER THE ELECTRICAL PLUG. Plugging the
electrical plug into an unsuitable supply circuit will damage the
equipment and may result in personal injury.
To reduce the risk of fire, do not operate equipment near open containers of
flammable liquids (gasoline).
Read and follow all caution and warning labels affixed to your equipment and
tools. Misuse of this equipment can cause personal injury and shorten the life
of the tire changer.
Keep all instructions permanently with the unit.
Keep all decals, labels, and notices clean and visible.
To prevent accidents and/or damage to the tire changer, use only Hunter
Revolution
Tire Changer recommended accessories.
™
Use equipment only as described in this manual.
Never stand on the tire changer.
Wear non-slip safety footwear when operating the tire changer.
Keep hair, loose clothing, neckties, jewelry, fingers, and all parts of body away
from all moving parts.
English
™
Tire Changer is solely responsible
™
Tire Changer is to
™
Tire
™
ALWAYS WEAR OSHA APPROVED SAFETY GLASSES. Eyeglasses that
have only impact resistant lenses are NOT safety glasses.
Do not let cord hang over any edge or contact fan blades or hot objects.
Wear proper back support when lifting or removing tire and or rim from the tire
changer.
The red "STOP" button, can be used for emergency stops.
Do not hose down, power wash or spray the unit with water.
Tire
Keep hands and clothing clear of moving parts. Keep hands
clear of rollers and clamp when in operation.
Do not lean or reach over tire changer when inflating.
Do not exceed these pressure limitations:
SUPPLY LINE PRESSURE (from compressor) 10.3 bar
OPERATING PRESSURE (gauge on regulator) 6.9 bar
BEAD SEATING PRESSURE (gauge on screen) 2.8 bar
Never mount a tire to a rim that is not the same diameter
(e.g., 16 1/2 inch tire mounting on a 16 inch rim.
Activate blast inflation nozzle only when seating beads.
Never point the blast inflation nozzle at yourself or others.
Remove any wheel assembly from the tire changer and reset all
tools at the end of the work day to prevent hydraulic fluid drain.
Bleed air pressure from the system before disconnecting air supply line
or other pneumatic components. Air is stored in a reservoir for operation
of the inflation components. Air pressure can be bled from the system by
pulling up on the knob located on the top of the regulator, and then turning it
counterclockwise.
Do not operate the blast inflation nozzle if the tire is not properly
clamped.
Hold the blast inflation nozzle firmly. The nozzle has a kick-back
and can strike the operator if not held firmly.
Do not operate the tire changer with worn rubber or plastic parts.
Wheels equipped with TPMS systems or special tire and rim designs may
require certain procedures. Consult manufacturer's service instructions.
SAVE THESE INSTRUCTIONS
Electrical
The Hunter Revolution
voltage and amperage rating.
Make sure that the appropriate electrical supply circuit is of the same voltage
and amperage ratings as marked on the tire changer.
DO NOT ALTER THE ELECTRICAL PLUG. Plugging the
electrical plug into an unsuitable supply circuit will damage the
equipment and may result in personal injury.
Make sure that the electrical supply circuit and the appropriate receptacle is
installed with proper grounding.
To prevent the possibility of electrical shock injury or damage to the
equipment when servicing the balancer, power must be disconnected by
removing the power cord from the electrical power outlet.
In the event of radio interference, the display may flicker - this is normal.
Specific Precautions/Power Source
The Hunter Revolution
source that will apply 208-230VAC, 1 phase, 24 amp 50 or 60 Hz, power cable
includes NEMA 30 amp plug, L6-30P, between the supply conductors of the
power cord. The Revolution Tire Changer is also capable of operating on
210-240VAC, 50 Hz at 24A for use in the international market. The power cord
supplied utilizes a twist lock connector, NEMA L6-30P.
This machine must be connected to a 30 amp branch circuit, or as directed by
local ordinances. The branch circuit shall be installed near the equipment and
Tire Changer is manufactured to operate at a specific
™
Tire Changer is intended to operate from a power
™
Image 1.
7
Publicidad
