Publicidad
Idiomas disponibles
Idiomas disponibles
1. unplug the miter saw.
2. Align the miter table to 0° and lock the saw head down in the transport position.
3. Loosen the bevel lock handle (17) at the rear of the saw with the saw arm at 0° bevel (blade 90° to the miter table).
4. Place a combination square on the miter table and the flat part of the saw blade (making sure the square is not touching any blade teeth).
5. Slowly rotate the blade by hand checking the square's alignment with the blade at several points. The edge of the square and blade should be
parallel; however, if the top or bottom of the blade angles away from the square's edge, an adjustment is needed.
6. using a 13mm wrench, loosen the lock nut (b), securing the positive bevel stop adjustment bolt (a) in place. The 0° bevel adjustment bolt is located
on the right lower portion of the bevel knuckle. (FIG 7)
7. use a 13mm wrench to turn the adjustment bolt (a) and so that the saw blade is in alignment with the square. (FIG 7)
8. Retighten the lock nut (b). Retighten the bevel lock handle. Recheck the blade to table alignment as in steps 4 and 5.
9. If necessary, loosen the bevel angle indicator pointer and adjust it to point accurately to the 0° line, then retighten the screw.
NOTE: To set the positive bevel stop for 45° use the above procedure utilizing a 45° triangle or the 45° side of the
combination square. The 45° bevel adjustment bolts (c-Fig 7) is located on the left lower portion of the bevel knuckle.
c
FIG 7
LASER ALIGNMENT
WArning:
Laser light – do not stare into the beam, aperture, or into a reflection from a mirror-like surface.
WArning:
Avoid exposure – laser light is emitted from the rear guard aperture. Use of controls or adjustments,
or performance of procedures other than those specified herein may result in hazardous laser light exposure.
WArning:
DO not disassemble the laser module.
WArning:
USE of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
WArning:
BE sure that the tool is switched off and unplugged from the power source before performing any
work on the tool. Failure to unplug the saw may result in accidental start-up, causing possible serious personal injury.
The laser alignment was made at the factory and is set for the center of the Blade or Draw line. Adjustment may be required prior to initial use due to
the effects of shipping and handling. you also have the ability to adjust the line projected by the laser to your liking. you may wish for the laser to be to
right or left of the blade, or straight on a drawn cut line. Where you ultimately decide to align the laser in relation to the saw blade's cutting path will
determine how you align the cut line.
On each side of the laser are 2 Phillips head screws (d) which, when loosened, allow movement to the left and right. The screw (e) on the laser's stem
area also allows left/right movement, but more importantly will affect the straightness of the laser line. Beware that small adjustments can yield dramatic
changes in the laser's path. With patience and practice you'll be able to place the laser line in the ideal position for your style of blade to cut line
alignment. (FIG 8)
OPErATiOn
WArning:
Always be sure the miter saw is disconnected from the power source before making any
adjustments or setting up prior to cutting. Failure to disconnect or unplug the machine may cause accidental starting,
resulting in serious personal injury.
LOCKING AND UNLOCKING THE CUTTING HEAD
When storing or transporting the miter saw, the cutting head should be locked in the
down position.
To lock down the cutting head,
1. Lower the cutting head completely.
2. Pull back on locking knob (24) outwards from its parked "unlock" (b) position.
3. Align locking shaft with locking hole (c),
4. Rotate the locking knob a 1⁄4 turn, and then release it to "Lock" (a) position
5. The locking shaft should insert into locking hole to lock the cutting head. (FIG 9)
10" Compound Laser Miter Saw
Operator's Manual
17
a
b
FIG 8
FIG 9
GMS15LB
e
d
a
c
b
24
Publicidad
