Makita 6924N Manual De Instrucciones página 3

Llave de impacto degollante
Ocultar thumbs Ver también para 6924N:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

19. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of starting
the power tool accidentally.
20. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
21. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
Ampere Rating
More Than
Not More Than
0
6
10
12
SHEAR WRENCH SAFETY RULES
Hold power tool by insulated gripping sur-
1.
faces, when performing an operation where
the fastener may contact hidden wiring or its
own cord. Fasteners contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
2.
Before using power tool, make sure that the outer
sleeve smoothly turns by hand. When it does
not smoothly turn, never use it and ask MAKITA
Authorized Service Center for check and repair.
3.
When sheared bolt tip falls without moving tip
ejector (tip lever), never use it and ask MAKITA
Authorized Service Center for check and repair.
4.
Always be sure you maintain good balance
and firm footing.
Be sure no one is below when using the tool in
high or elevated locations.
5.
Hold the tool firmly.
6.
Use care and common sense when disposing
of sheared bolt tips. Falling tips from high
locations or scattered tips can cause severe
injury.
SAVE THESE INSTRUCTIONS.
Table 1: Minimum gage for cord
Volts
120V
220V - 240V
6
10
12
16
23. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Service
24. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
25. Follow instruction for lubricating and chang-
ing accessories.
26. Keep handles dry, clean and free from oil and
grease.
USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating. Table 1 shows the correct size
to use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord.
Total length of cord in feet
25 ft.
50 ft.
50 ft.
100 ft.
AWG
18
16
18
16
16
16
14
12
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace strict
adherence to shear wrench safety rules for the subject
product. MISUSE or failure to follow the safety rules
stated in this instruction manual may cause serious
personal injury.
Symbols
The followings show the symbols used for tool.
volts
amperes
hertz
alternating current
no load speed
3 ENGLISH
100 ft.
150 ft.
200 ft.
300 ft.
16
14
14
12
14
12
Not Recommended

Publicidad

Tabla de contenido
loading

Tabla de contenido