Publicidad
Idiomas disponibles
Idiomas disponibles
– Do not operate the light near flammable liquids or in gaseous or explosive atmospheres.
Internal sparks may ignite fumes causing personal injury.
– Do not expose this unit to extremely high temperatures, flames or sparks.
• To reduce the risk of injury, close supervision is necessary when the light is used near children.
• Store idle appliances indoors. When not in use, appliances should be stored indoors in dry and
high or locked-up places – out of reach of children.
• Use of accessories and attachments. Use only attachments recommended or sold by the
manufacturer.
• Check for damaged parts. A part that is damaged should be properly repaired or replaced by
manufacturer before further use unless otherwise indicated elsewhere in this instruction manual.
Have defective switches replaced by manufacturer. Do not use this appliance if the on/off button
does not turn it on and off.
• Do not operate this unit with a missing or damaged lens.
• Do not touch the LED surface at any time.
• Never look directly into the light or shine the light into another person's eyes.
• Do not disassemble the main body of the unit. Other than the 3 "AA" size dry cell batteries, there
are no user-replaceable parts.
ALKALINE BATTERY SAFETY INSTRUCTIONS
WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk:
• Use only "AA" alkaline dry cell batteries in this unit.
• Carefully follow all instructions and warnings on the battery label and package.
• Always insert batteries correctly with regard to polarity (+ and –), marked on the battery and the
equipment.
• Do not short battery terminals.
• Do not charge batteries.
• Do not mix old and new; or alkaline, standard (carbon-zinc) and rechargeable (nickel cadmium or
nickel metal hydride) batteries. Replace all of them at the same time with new batteries of the
same brand and type.
• Remove dead batteries immediately and dispose of per local codes.
• Do not dispose of batteries in fire.
• Keep batteries out of reach of children.
• Remove batteries if the device will not be used for several months.
"Transporting batteries can possibly cause fires if the battery terminals inadvertently come in
contact with conductive materials such as keys, coins, hand tools and the like. The US Department
of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in
commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly
protected from short circuits. So when transporting individual batteries, make sure that the battery
SB01AL_SBALCSB_SBALCSR_SBALCSY_Manual_ENSP_051614.indd 4-5
4
terminals are protected and well insulated from materials that could contact them and cause a short
circuit."
SAVE THESE INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new
Stanley
and follow the instructions carefully before using your new light.
POWER SUPPLY
The unit is powered by three "AA" alkaline dry cell batteries (may be sold separately). Unscrew the
back cover screw (counter-clockwise) and remove the back cover. Gently pull the battery strap to
remove the old batteries. Pull the strap gently so as not to break it. Insert batteries as described in
compartment, making sure the battery strap is first replaced beneath the new batteries, observing
the cautions that follow. Replace and secure the back cover by screwing the back cover screw
clockwise. Do not be over-tighten.
CAUTIONS
• When replacing the "AA" alkaline dry cell batteries: DO NOT mix old and new batteries. Always
insert batteries correctly with regard to polarity (+ and –), marked on the battery and the
equipment. Remove dead batteries immediately and dispose of per local codes.
• Follow all warnings regarding batteries in the Important Safety Instructions section of this manual.
OPERATING THE LIGHT
Position the unit, adjusting the flexible stand's legs or detaching the light and positioning using the
magnetic discs as desired. Press the light mode pushbutton on the top of the unit.
• Press once for high intensity.
• Press again for medium intensity.
• Press a third time for to turn the light off.
• Press and hold the light mode pushbutton for about five seconds for flashing LEDs.
Detaching the light from the flexible stand
To detach the light:
• Slide the attachment bar out of the light holder groove.
Once the light is detached, the magnetic discs allow you to position it on any metallic surface.
To attach the light back on the stand:
• Slide the attachment bar back into the light holder groove.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
• When light is attached using the either the flexible stand or magnetic discs, do not shake the light
or object that it is attached to. Do not attach the light to any electrical wires or anything that it is
not secure.
Flexible Work Light.
Read this Instruction Manual
®
5
5/16/2014 11:18:16 AM
Publicidad
