Publicidad
Idiomas disponibles
Idiomas disponibles
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to be recharged.
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.
Wall Mounting
Some D
WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Torque
WARNING: This is a high‑torque drill. To reduce the
risk of serious personal injury, ALWAYS hold tool firmly
with both hands in the proper position for operation
as shown.
Torque is the twisting action the drill produces in regards
to the rotating bit. As the drill bit meets resistance in the
material being drilled, the motor responds by adjusting the
output torque to meet the requirement up to the maximum
capacity of the motor and gear system.
E‑Clutch® System (Fig. A)
The DCD130 is equipped with the D
E‑Clutch® System. This feature senses the motion of the
tool and shuts the tool down if necessary. The red LED
8
indicator
illuminates when the E‑Clutch® System
is engaged.
INDICaToR DIaGNosIs
OFF
Tool is functioning
normally
SOLID
E‑Clutch® System
has been activated
(ENGAGED)
Side Handle (Fig. A, D)
WARNING: To reduce the risk of personal injury,
ALWAYS operate the tool with the side handle properly
installed. Failure to do so may result in the side handle
slipping during tool operation and subsequent loss of
control. Hold tool with both hands to maximize control.
9
The side handle
can be placed in either side of the drill
or the top of the drill according to operator preference and
available working clearance.
Installing and Removing the Chuck Key
(Fig. A, E, F)
Your tool is provided with a chuck key
on the foot of the tool. To install the chuck key into its holder,
slide the flat head of the chuck key handle into the chuck
10
key holder
as shown. Snap the handle's shaft into the
11
retention clip
on the holder.
To remove the chuck key from its holder, pull the chuck key
handle out of the holder and slip the flat head out of the hole.
NoTE: To avoid losing the chuck key, do not store it in any
other orientation.
Installing and Releasing a Bit (Fig. A)
Open the keyed chuck jaws by turning the collar by hand
then insert the shank of the bit about 3/4" (19 mm) into
chuck. Tighten the chuck collar by hand. Place chuck key (
Fig. A) in each of the three holes, and tighten in clockwise
direction. It's important to tighten chuck with all three holes.
To release the bit, turn the chuck counterclockwise in just
one hole, then loosen the chuck by hand.
NoTE: When using hex shank or three‑sided shank bits, be
sure to align the flat sides of the bit with the chuck jaws to
ensure the bit is properly engaged by the jaws.
Worklight (Fig. A)
CAUTION: Do not stare into worklight. Serious eye
injury could result.
7
The worklight
is activated when the trigger is depressed,
and will remain on for a short time after the trigger is
ENGlIsh
WALT anti‑rotation
e
solUTIoN
Follow all warnings and instructions
when operating the tool.
With the tool properly supported,
release trigger. The tool will function
normally when the trigger is
depressed again and the indicator
light will go out
6
that can be stored
6
,
29
Publicidad
