Good Earth Lighting SE1091-WH3-01LF0-G Manual página 2

Installation For Round Surface Mount Electrical Boxes
AA/BB
GG x1
x2
FF x1
Pull supply wires out of the electrical box. Using machine screws (AA or BB), secure mounting strap (FF) to the electrical box. Ensure the side marked "FRONT" is
facing out. Remove protective paper from adhesive face of foam gasket (GG). Pull supply wires through the opening in gasket and adhere gasket to the mounting strap
and outer edge of round surface electrical box.
Pull supply wires out of the electrical box. Using machine screws (AA or BB), secure mounting strap (FF) to the electrical box. Ensure the side marked "FRONT" is
facing out.
DD x1
Fixture must be properly grounded. Connect fixture ground wire to ground
wire in electrical box using wire nut (DD). These wires can be either green or
bare copper. Insert black supply lead into connector on black fixture wires
and white supply lead into connector on white fixture wires. Push excess
wire into electrical box.
NOTE: If eave mounting the fixture, the Dusk-to-Dawn sensor must be
facing outwards.
Operation Instructions
HH x1
The fixture comes with a built in Dusk-to-Dawn sensor. If the security light
cycles ON and OFF, the Dusk-to-Dawn sensor may be activating due to
reflected light from a nearby surface. Place the directional sensor cap (HH)
firmly over the Dusk-to-Dawn sensor. This should prevent extraneous light
from "tripping" the Dusk-to-Dawn sensor.
To disable the Dusk-to-Dawn sensor, install the sensor cap (II) over the
Dusk-to-Dawn sensor. This will prevent the Dusk-to-Dawn sensor from
controlling the ON/OFF function and should allow control from the
wall switch.
Troubleshooting Guide
Problem
Fixture doesn't light.
Fuse blows or circuit breaker trips
when light is turned on.
Good Earth Lighting® 1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
II x1
Before doing any work on the fixture, shut off power supply at the circuit breaker panel
to avoid electrical shock.
Cause
Power is off.
Bad connection.
Bad switch.
Discontinue use.
Installation For Recessed Electrical Boxes
AA/BB
x2
FF x1
FF x1
EE x1
Position fixture over the mounting strap. Secure long machine screw (CC)
through the center hole of the wall plate and mounting strap. NOTE: Ensure
gasket (GG) properly seals gap between wall plate and electrical box to
prevent water seepage into electrical box. Restore power to the electrical
box and ensure that the light is functioning properly. If the light is functioning
properly, fit the silicone cap (EE) into the mounting screw opening to prevent
water seepage into the housing.
For recessed electrical boxes, use silicone adhesive caulking (not included)
to seal the gap between the wall plate and the mounting surface to prevent
water seepage into the electrical enclosure.
Good Earth Lighting
®
The manufacturer warrants this lighting fixture to be free from defects in materials
and workmanship for a period of (6) years from the date of original purchase by the
consumer. The fixture is not warrantied for use in a commercial or retail application.
The warranty is limited to use in a residential environment. We will repair or replace
(at our option) the unit in the original color and style if available, or in a similar color
and style if the original item has been discontinued, without charge. Defective units
must be properly packed and returned to the manufacturer with a letter of explanation
and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to
obtain a return authorization number and an address where to ship your defective
product. Note: C.O.D. shipments will NOT be accepted. The liability of the
manufacturer is in any case limited to replacement of the defective light fixture
product. The manufacturer will not be liable for any other loss, damage, labor costs or
injury which is caused by the product. This limitation upon the liability of the
manufacturer includes any loss, damage, labor costs or injury which is (I) to person or
property or otherwise; (II) incidental or consequential in nature; (III) based upon
theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV)
directly, or indirectly related to the sale, use, or repair of the product. This warranty
gives you specific rights, and you may also have other rights which vary from state to
state.
Solution
Check if power supply is on.
Check cords and/or wiring.
Test or replace switch.
Call customer service.
Printed in China
Electrical Boxes
Silicone
- 6 YEAR LIMITED WARRANTY
Replacement Parts List
Hardware Kit:
ZH-SE1091F01
SAVE THESE INSTRUCTIONS.
For Recessed
2