Scope Of Use; Protective Cap - Rothenberger 036060 Instrucciones De Uso

SCOPE OF USE

This gas soldering iron set is designed for soft soldering electrical wires and circuit boards, removing or drying paint
and forming plastic. It can also be used for shrink fitting and softening or removing adhesive. The machine may only be
used for its intended purpose.
IGNITING AND EXTINGUISHING THE FLAME (see cover)
- Push the safety lock button down and pull the iginition switch to ignite the flame.
- Release the ignition switch to extinguish the flame.
C C o o n n t t i i n n u u o o u u s s f f l l a a m m e e
- Move the continuous flame switch into the CONTINUOUS postion to lock the igintion switch in position.
- Slide the continuous flame switch into the OFF position to extinguish the flame.
L L i i m m i i t t t t h h e e t t e e m m p p a a r r a a t t u u r r e e
- Regulate the flame with the flame level adjustment.
FITTING THE ATTACHMENTS
C C a a u u t t i i o o n n ! !
T T h h e e m m e e t t a a l l a a t t t t a a c c h h m m e e n n t t s s g g e e t t e e x x t t r r e e m m e e l l y y h h o o t t d d u u r r i i n n g g o o p p e e r r a a t t i i o o n n . . N N e e v v e e r r t t o o u u c c h h h h o o t t a a c c c c e e s s s s o o r r i i e e s s ! !
A A l l l l o o w w t t h h e e t t o o o o l l t t o o c c o o m m p p l l e e t t e e l l y y c c o o o o l l d d o o w w n n b b e e f f o o r r e e y y o o u u c c h h a a n n g g e e a a n n y y a a c c c c e e s s s s o o r r y y . .
U U s s e e a a s s a a s s o o l l d d e e r r i i n n g g i i r r o o n n
- The tool is factory fitted as a soldering iron and can be used as
such immediately.
U U s s e e a a s s a a h h o o t t a a i i r r g g u u n n
- Unscrew soldering tip drom the hot air / soldering attachment to
use the tool as a hot air gun.
- If necessary the hot air deflector can be slid on the hot air attach-
ment. The deflector can be rotated once mounted.
U U s s e e a a s s a a g g a a s s t t o o r r c c h h
- Unscrew the knurled nut to separate the hot air / soldering attach-
ment from the gas torch attachment. Subsequently refit the gas
torch with the knurled nut. The tool can now be used as a gas
torch.
R R e e s s t t i i n n g g t t h h e e d d e e v v i i c c e e
- A tool rest is integrated in the handle. Always use the tool rest
when putting the item down.

Protective cap

C C a a u u t t i i o o n n ! !
T T h h e e p p r r o o t t e e c c t t i i v v e e c c a a p p m m u u s s t t n n o o t t b b e e f f i i t t t t e e d d w w h h e e n n t t h h e e f f l l a a m m e e i i s s i i g g n n i i t t e e d d . .
- A protective cap is included in the scope of delivery. Use the pro-
tective cover to safely rest the hot device and to prevent mechani-
cal hazards.
- Slide the protective cap firmly on the locking nut.
RECYCLING
Worn out tools must be recycled at a suitable recycling facility.
Do not dispose of in the household waste.
3 3