Publicidad
VII.
OPERATION.
EN
Switch on the electric water heater
1.
Before initial start of the appliance, please make sure that the water heater has
been correctly connected to the electrical network and that it is filled up with
water. Switching on the water heater is done through the device incorporated
in the installation, which is described in sub-item 3.3 of section V, or by
inserting the plug into an electrical socket (for models with cord with a plug).
2.
Description of the control panel of the appliance
1
2
3
4
Button and element designation:
1 -
Program selection button and activation of programming functions in
the "Weekly Programmer" regime
2 -
Button for selection of the day of the week.
3 -
Time / period selection button in different modes
4 -
"Handset" button to select number of showers and activate the "Manual
control" mode.
5 - LCD display.
6 -
Device on / off button - Standby mode.
7 -
ECO SMART, ECO NIGHT or ECO COMFORT mode selection button
8 -
"BOOST" function selection button
9 -
On / Off button for Vacation Mode
Possible combinations:
7 + 8 -
+
"locking" of the panel
8 + 9 -
+
Turning the Wi-Fi Module On or Off (Stand By Mode)
2 + 3 -
+
Copy the status of the current cell
1 + 2 -
+
Vertical to horizontal orientation of the display
3.
Switching on the electronic operation of the appliance
Switching on is done by pressing button
the mode which is to be used and, depending on the type of mode, the symbols
described for each mode below.
Switching off the electronic operation is done by pressing button
Setting up and operation of the appliance
4.
•
Switching on and off the Wi-Fi module (for models with Wi-Fi).
Switching on and off the Wi-Fi module is done by simultaneously pressing the
buttons
+
for minimum 10 seconds in stand-by mode, i.e. when the
appliance is switched off from button
display shows the following symbol
•
Setting the time and day of the week
In order for the programme modes to work properly you must set the current
time and day of the week. Setting up is done in stand-by mode, i.e. when the
appliance is not switched on. Hold the
blinking in the weekday selection field. Using the button
day of the week. Press button
of the timer start blinking. Using the button
. The second group of digits starts blinking. Again, using button
minutes and confirm with button
•
Vertical to horizontal orientation of the display
In order for the program modes to work correctly when installing the appliance
horizontally, it is obligatory to select a "horizontal" mode of operation
(horizontal orientation of the display). To switch between horizontal and
vertical symbols and vice versa, you need to press and hold the two buttons
+
for 5 seconds when the water heater is a standby mode.
WARNING: Your TESY electric water heater is of the highest energy class. The
class of the appliance in ECO mode is guaranteed only When the display
orientation is correct.
•
"Manual control" mode
Using button
you can select the "Manual control" operating mode. The symbol
and the countdown timer are shown on the display if the appliance is in a warm-
up or clock mode, if the appliance is ready for use.
When you turn on the manual mode, the screen shows the last saved preset
number of showers. The maximum number of showers that can be selected
depends on the model and is shown in table 1.3.
8
5
6
7
8
. By doing so the display will show
. When the Wi-Fi module is on, the
.
button. The day of the week starts
select the current
to confirm the selection. The first two digits
set the time and confirm with
.
•
"Аnti-freezing" function
The Аnti-freezing function is active with the following modes: Manual control
and Weekly Programmer.
To turn the Аnti-freezing mode on, you need to press button
the symbol appears.
WARNING: The electrical power supply of the device should be switched on. The
safety valve and the pipe connecting it to the device must be secured against
freezingter.
•
"Weekly programmer" mode
9
By pressing button
modes - P1, P2 or P3.
To set up the program you have selected, press and hold button
setting it.
The device enters programming mode for the selected program. The program
indicator (P1, P2 or P3) flashes on the display.
Step 1 - Choose a day of the week
Using button
select the day of the week for which you will change the program.
Step 2 - Select the desired time
Using button
select the desired time.
Step 3 – Select the desired amount of hot water
With button
select the number of showers to indicate the required amount
of hot water for the desired time. You can choose *, 1, 2, ... number of showers by
pressing the button
"*" means that the anti-freeze mode is selected, which is displayed with the symbol
.
By using the combination of buttons
showers) from the current hour to the next hour.
To do this, press and hold button
hour (neighbouring cell), copying the selected number of showers.
A cell is provided in the hour chart for each hour of the day. The numbers
below are guiding you.
Indication key:
.
- When the time cell is full there is a requirement for hot water at that time
and the water will be heated depending on the number of showers selected.
- if the time cell is empty, the device has no task set for that time
The changes made are confirmed by pressing button
appliance will exit the setup mode.
In case the buttons are not manipulated for a long time, the changes are
automatically saved (even if they have not been confirmed).
Program modes - P1 и P2
For programs P1 and P2, you can select which day of the week, at what time
what amount of hot water you need. The appliance calculates when to turn on
in order to provide the required amount at the set time.
Example:
If you have set that you need to have hot water for 3 people on Wednesday at
18:00, the appliance will maintain that amount for a certain period of time and will
set the
then shut down.
Program mode - P3
For P3 programs, you can select the day of the week, the duration of operation
of the appliance and the amount of hot water it needs to provide. The
appliance switches on and tries to reach the set number of showers.
If you have set that on Wednesday at 18:00 you need to have hot water for 3
showers, the appliance will start heating the water at this time until it reaches
the 3 showers set.
•
ECO SMART, ECO NIGHT and ECO COMFORT mode
By pressing button
EC0 - ECO SMART,
EC1 - ECO NIGHT (SMART algorithm with night-time heating priority),
EC2 - ECO COMFORT ((the lowest limit provides 2 showers, the upper limit
generates economy).
The selected mode is displayed on the screen.
Attention! Your TESY electric water heater is of the highest energy class. The
class of the appliance is guaranteed only when it operates in ECO mode "Eco
Smart" due to the significant energy savings that are generated.
, you can select one of the three built-in weekly program
.
+
you may copy settings (number of
and by pressing button
you can choose between three modes:
until to display
to start
move to the next
, once and the
Publicidad
