Publicidad
OBJ_BUCH-594-004.book Page 13 Friday, April 29, 2016 4:50 PM
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Cutting board: a
=5.0 m/s
, K=1.5 m/s
h
Cutting wooden beam: a
=5.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards:
EN 60745-1, EN 60745-2-11, EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Henk Becker
Helmut Heinzelmann
Executive Vice President
Head of Product Certification
Engineering
PT/ETM9
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
Before any work on the machine itself, pull the mains
plug.
Auxiliary Handle
Mounting the Auxiliary Handle (see figures A – C)
Slide the spacer tube 14 into the housing and tighten with the
knurled screw 13.
Spread the auxiliary handle 2 somewhat and place it over
both ends of the spacer tube 14.
Insert screw 16 through the auxiliary handle and the spacer
tube and tighten with the knurled nut 15.
Bosch Power Tools
Changing the position of the auxiliary handle
(see figure D)
2
,
The auxiliary handle 2 can be set to any position for a secure
2
2
, K=1.5 m/s
.
and low-fatigue working posture.
Loosen the knurled nut 15 and adjust the auxiliary handle 2 to
the requested position. Tighten the knurled nut again.
Offsetting the Auxiliary Handle (see figure E)
For sawing close to edges, the auxiliary handle 2 can be off-
set.
Loosen the knurled screw 13 and slide the auxiliary handle 2
with the spacer tube 14 to the requested position. Tighten the
knurled screw again.
Inserting/Replacing Saw Blades
Wear protective gloves when mounting the saw blades.
Danger of injury when touching the saw blades.
Whenever working on the machine, always mount the
saw blade guard 11 on the saw blades.
Choice of Saw blades
Choose the saw blades with respect to the material being
worked.
For sawing light building materials, only use carbide-tipped
saw blades. Do not use saw blades intended for sawing wood
or plastics.
Inserting the Saw Blades (see figures I – J)
Turn the machine around so that the base plate faces upward.
If required, remove the extraction duct 8 (see "Extraction
Duct", page 14).
Always insert the saw blade first whose corresponding driving
pin 17 is closer to the motor.
Note: Each time after switching off, the driving pins 17 for the
saw blades are in a different position. The illustration shows a
random position.
The lettering on the saw blade 12 must always face out-
ward and correspond with the colour of the driving pin
17.
Press and hold the SDS button 9. This causes the engaging
pin 18 to move back and the saw blades can be hooked in.
Hook the fitting saw blade 12 onto the saw blade driving pin
17 closest to the motor (). Swing/work the saw blade into
the saw blade guide 19 and allow the nose of the saw blade to
engage in the opening of the sword 1.
Hook the second saw blade onto the free saw blade driving
pin 17 (). Swing/work the saw blade into the saw blade
guide 19. Release the SDS button 9.
From above, press on the second saw blade 12 until the nose
of the saw blade engages in the opening of the sword 1.
Check the saw blades for firm seating. A loose saw blade
can fall out and cause injury.
Mount the saw blade guard 11 onto the saw blades 12.
Removing the Saw Blades (see figures K – L)
Press the SDS button 9. Pull both saw blades 12 close to
the saw blade driving pins 17 together out of the saw blade
guide ().
English | 13
1 609 92A 2PW | (29.4.16)
Publicidad
