Husqvarna LC 141iV Manual De Usuario página 21

Note:
The battery charger must be connected to the
voltage and frequency specified on the rating plate.
The battery does not charge if the battery temperature
is above 50°C. The battery charger decreases the
temperature of the battery before it starts to charge.
1. Connect one end of the power cord for the battery
charger into the socket of the battery charger.
2. Connect the other end of the power cord for the
battery charger in an grounded mains socket. The
LED on the battery charger flashes green one time.
(Fig. 45)
3. Put the battery in the battery charger. The green
light on the charger comes on when the battery is
correctly connected to the battery charger. (Fig. 46)
4. When all LEDs on the battery have come on the
battery is fully charged. Charge the battery for
maximum 24 hours.
5. To disconnect the battery charger from the mains
socket, pull the plug, not the power cord.
6. Remove the battery from the battery charger.
Battery charging status
A Husqvarna Li-ion battery can be charged or used at
all charging levels. The battery is not damaged. A fully
charged battery will not decrease its charge when the
battery is left in the charger.
LED display
LED 1 flashes
LED 1 is lit, LED 2 flashes 25%-50%
LED 1, LED 2 are lit, LED
3 flashes
LED 1, LED 2, LED 3 are
lit, LED 4 flashes
LED 1, LED 2, LED 3,
LED 4 are lit
To operate LC 141iV and LC 141i
To start the product
1. Put a charged battery in the battery compartment.
2. Turn the safety key to 1. (Fig. 27)
3. Stay behind the product.
4. Press the ON/OFF button (A) on the control panel
and the green LED (B) comes on. (Fig. 47)
5. Loosen the start inhibitor. (Fig. 48)
6. Push the motor brake handle in the direction of the
handlebar. (Fig. 49)
919 - 011 - 16.08.2023
Charging status
0%-25%
50%-75%
75%-100%
Fully charged
To use the drive on the wheels
• Model LC 141iV. Pull the drive bail in the direction of
the handlebar to start the drive. (Fig. 50)
• Press + and - on the control panel to set the drive
speed in 4 steps. (Fig. 51)
• Release the drive bail to disengage the drive, for
example when you go near an obstacle.
To use the SavE function
The product has a battery saving function (SavE) that
gives longer operation time.
1. Press the SavE button (A) to start the function. The
green LED comes on. (Fig. 52)
2. Press the SavE button again to stop the function.
The green LED (B) goes out.
The SavE function stops automatically if the ground
conditions make it necessary to have a higher output.
The SavE function starts automatically when the ground
conditions lets it.
High load function
When the product cuts long or wet grass, the motor
automatically increases rpm. The motor goes back to
standard mode when high load is not necessary.
To stop the product
The product stops automatically if you do not operate it
for 10 minutes. Always turn the safety key to 0 before
you let the product out of view.
1. Release the motor brake handle to stop the motor.
(Fig. 26)
2. Press the ON/OFF button (A) on the control panel
and the green LED (B) goes out. (Fig. 53)
3. Open the battery lid and turn the safety key to 0.
(Fig. 54)
4. To remove the battery, press the 2 release buttons
and pull out the battery. (Fig. 55)
5. Charge the battery if it is weak. For more
To charge the battery on page 20 .
information, see
To operate LC 141C
To select an approved cable (LC 141C)
Note:
For the UK market, use only the 16M extension
cable that comes with the product. For all other markets,
refer to the information below.
If extension cables are used, these must comply with the
minimum cross-sections in the table below:
Voltage
220-240V/ 50Hz
Cable Cross sec-
length tion
2
Up to 20 m 1.5 mm
21