Publicidad
Idiomas disponibles
Idiomas disponibles
•
Slide down the wall brace in order to detach it from the back of the body.
•
Attach firmly the wall brace onto a wall through the four screw holes.
•
Lift the panel heater up to almost vertical position and insert the two lower
protruding parts of the braces into the two lower openings of the back
cover of the panel heater. Then lift the panel heater and insert the two upper
protruding parts of the wall braces into the two upper openings of the back
cover of the heater. Finally, put the two screws back to their places and
tighten them in order to install the panel heater firmly to the wall.
BATHROOM OPERATION
•
The panel heater must be installed in accordance with the normal trade
practices and in compliance with the national legislation (EU electricity
directives and regulations concerning special installations and places
of operation including bathrooms, shower cabins HD60364-7-701(IEC
60364-7-701:2006)).
•
In case this panel heater is to be used in a bathroom or other similar room,
the following installation requirements must be observed: the panel
heater is with IP24 protection (water drops protection). Hence it can be
installed in "Volume 2" (see the diagram below) in order to avoid the risk of
the control board (power switch and thermo regulator) being reached by
a person who is in a shower or a bathtub. The minimum distance between
the appliance and a water source should be not less than 1 meter and it
is compulsory the appliance to be wall-mounted! If you do not feel sure
about the installation of this panel heater in a bathroom, we recommend
you to consult a professional electrician.
Note: If the above-mentioned instructions cannot be implemented, it is
recommended to install the appliance in "VOLUME 3".
•
In wet premises the power source must be installed at a height of at least
25 cm above the floor (bathrooms and kitchens).
•
The installation must be equipped with a safety fuse, and the distance
between the fuse contacts in disconnected condition should be at least 3 mm.
Thank you for choosing CN051 / CN031 panel heater. This is a product
providing heating in winter depending on the consumers' needs for
comfortable room temperature. If operated and taken care of properly in
accordance with these instructions, the appliance will provide you with
many years of useful operation.
OPERATION INSTRUCTIONS
1. Predefined functions:
Comfort mode
; Eco mode
English
; Sleep mode
1.1. Comfort mode - with On/Off option - allows the user to set a desired
temperature when being at home. After once set it and the function is
switched On, the appliance will keep the same room temperature each time of
usage. This temperature to be set at 23°C by default.
Activation and deactivation of Comfort mode - /Quick start A1/
When the convector is in „Heating mode„ ,sign „sun„
the
display.
1.2. Eco mode
- with On/Off option - allows the user to set a desired
temperature when being out of home. After once set it and the function is
switched On, the appliance will keep the same room temperature each time of
usage. This temperature will be set at 18°C by default. User could also set the
time when the appliance to switch to Comfort mode.
Activation and deactivation of Eco mode - /Quick start A2/
When the set time has elapse, the appliance going to Comfort mode
1.3. Sleep mode
with On/Off option – two hours after activation, the
convector decreases the set temperature with -3°C under the set temperature
in Comfort mode. User could set the time range for operating in Sleep mode
then the appliance switches to Comfort mode. By default: 6 hours.
Activation and deactivation of Sleep mode - /Quick start A3/
When the set time has elapse, the appliance going to Comfort mode!
2.
Basic modes
"Heating" mode
Activation and deactivation of Heating mode - /Quick start B1/
The set temperature is indicating in the right. If the room temperature is lower
than the set one, the heater will switch automatically on, and a heating sign
will appear on the display.
Temperature adjustment
By pushing any of the buttons:
adjustment" mode and the user can change the temperature settings in
the desired direction. The new settings are saved and the heater goes
automatically into "Heating" mode
pressed longer than 0.5 sec., the temperature settings will start automatically
increase or decrease at a rate of 6 units per second. The range of available
temperature settings is from 10 up to 30 degrees.
Delay start function
The delay start function allows the user to set the time at which the convector will
switch on and start heating.
Activation and deactivation of Delay start function - /Quick start B2/
When the set time has elapse, the appliance going to Heating mode!
Initially a setting of 12 hours is set by default
If any of
or
buttons is held for more than 0.5 seconds, the time and
temperature settings start automatically increase or decrease at a rate of 4
units per second. Confirm with "Mode" button
for 3 seconds.
If user enters time – 00, this mode will not be implemented. If the "Delay start"
mode is already enabled and user selects the "Delay Start" mode again, it can
be changed the remaining time in both possible directions. You can exit this
mode by pushing the "On/Off"
button. Then panel heater will go into
"Heating" mode. The "Delay start" needs to be set from 0 to 96 hours.
Anti-frost mode
If the room temperature falls below 5°C and the panel heater is off, the heater
appears on
or
the user enters "Temperature
. If any of
or
buttons get
or don't press any button
Operation and Storage Manual of Panel Heater
EN
!
13
Publicidad
