Milwaukee M12 2458-20 Manual Del Operador página 4

Warning
pack before changing or removing ac-
cessories. Only use accessories specifically
recommended for this tool. Others may be
hazardous.
Warning
wear safety goggles or glasses with side
shields.
Fuel Gauge
To determine the amount of charge left in the bat-
tery, turn the tool ON. The Fuel Gauge will light up
for 2-3 seconds. To signal the end of charge, the
fuel gauge will flash 6 times and the tool will not
run. Charge the battery pack.
If the battery becomes too hot, the fuel gauge lights
will flash 6 times and the tool will shut down. If the
battery is too hot when the tool is turned on, the
fuel gauge will flash once and the tool will not run.
Allow the battery to cool down.
Trigger Lock
To lock the trigger, push the trigger lock to display
the lock symbol. The trigger will not work while the
switch is in the locked position. Lock the trigger when
storing the tool and when the tool is not in use.
To unlock the trigger, push the trigger lock to
display the unlock
Warning
always unplug the charger and remove the
battery pack from the charger or tool before per-
forming any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
milWaukee service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
After six months to one year, depending on use,
return the tool, battery pack and charger to a
MILWAUKEE service facility for:
• Lubrication
• Mechanical inspection and cleaning (gears,
spindles, bearings, housing, etc.)
• Electrical inspection (battery pack, charger,
motor)
• Testing to assure proper mechanical and
electrical operation
If the tool does not start or operate at full power
with a fully charged battery pack, clean the contacts
on the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to a MILWAUKEE service facility for repairs.
Always remove battery
To reduce the risk of injury,
symbol.
To reduce the risk of injury,
operaTion
Warning
body away from collet and magnetic
sleeve area of the tool. Fasteners hit by the
anvil can cause serious injury if they contact
the hands or body.
Operation
1. Insert a nail head into the mag-
netic sleeve. Note: To avoid
jams, only use nails with a head
diameter greater that 0.200".
Do not use nails with broken
heads.
2. Place the tip of the nail against
the workpiece.
3. Press the trigger button and
apply pressure to start the ham-
mering.
4. Continue to hammer until the
collet is against the workpiece
and the nail is flush with the
workpiece.
Clearing Jams
Nails with very small heads (< 0.200" diameter)
or broken heads could get jammed between the
magnetic sleeve and the anvil.
1. Remove battery pack.
2. Use a pliers to grasp the end of the nail and pull
it free from the collet. It may be necessary to
retract the magnetic sleeve to grasp the nail.
3. If the nail cannot be removed with pliers, unscrew
the collet to remove the nail from the jam.
mainTenance
Warning
injury and damage, never immerse your
tool, battery pack or charger in liquid or allow
a liquid to flow inside them.
Cleaning
Clean dust and debris from charger and tool
vents. Keep tool handles clean, dry and free of oil
or grease. Use only mild soap and a damp cloth
to clean the tool, battery pack and charger since
certain cleaning agents and solvents are harmful to
plastics and other insulated parts. Some of these
include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia
and household detergents containing ammonia.
Never use flammable or combustible solvents
around tools.
Repairs
For repairs, return the tool, battery pack and char-
ger to the nearest service center listed on the back
cover of this operator's manual.
4
Always keep hands and
To reduce the risk of personal