Publicidad
Idiomas disponibles
Idiomas disponibles
6.
CLEANING OF THE INTERNAL GLASS PANELS
1.
Only clean the internal component and glass panels with a soft,wet sponge and a neutral detergent.
2
. Dry with care using a soft cloth
External cleaning
1
.For the glass panels use the same products as used for the internal cleaning.
protection tape from the steel panel and from the grids.
7. CONNECTION TO MAINS
1
.
Ensure that mains voltage and frequency are the same as those stated on the rating plate ( ) attached
to the appliance.
2.
Ensure that the supply socket has the following characteristics:
earthed.
b)
It is appropriate for the nominal current as set out on the rating plate.
-
IEC regulations: Magneto-thermic differential switch with In = nominal value as stated on the rating plate;
-
Differential with Id sensitivity = 30 mA.
4
.
The connecting cable to the appliance is H05 VVF, designed for internal use only. For different setting it
is necessary to change it (for example H07 VVF for external settings)
during the trasport or storage, has been erroneously placed in horizontal position or upside-down, it must
be left in the correct position for at least 3 hours before connecting it to the electrical supply.
plug (do not use triple and reduction outlets) (see picture 6).
8. CONTROLS
The controls of the appliance are situated at the front inside a protected rectangular recess. .
switch:
to run the rotating shelves. For safety reason, the rotation stops immediately when opening the
door or if encountering even a slight obstruction. .
appliance. .
3 Refrigeration switch:
temperature inside the appliance.
adjiust the temperature: pushing once the button
the cell, pushing several times the button
7 "DOWN"
the button
the temperature decreases (see picture 7).
9. CHECKING THE CORRECT FUNCTIONING
MAKE SURE THAT:1
. T
he plug is connected
thermometer shows the desired temperature for the foodstuffs to be stored in. . Internal light and rotation
swiches are on. . The door is closed. . The appliance is not exposed to the direct light of the sun or to
5
high powered lamps. . The room temperature does not exeed that in which the appliance is designed to
7
work normally, i.e. +30° C 55% r.h. (Climatic class 4). . The compressor ventilation grilles are free from
obstruction for at least 30 cm. .The foodstuffs are placed on the shelves in the right way, in order to
ensure a good circulation of the cool air, especially berween the side glass panels and the shelves,
where the air outlets are.
10. INTERNAL CLEANING (EVERY 15 DAYS)
1
. Switch off electricity supply. . Open the door and remove the displayed foodstuffs. . Wipe the internal
surfaces and the accessories of the appliance with a sponge dipped in water with a little bicarbonate of
soda. Dry with care.
11. REPLACEMENT OF INTERNALIGHT
1
. Switch off electricity supply. . Unscrew the screws fixing the upper light holder. . Detach the
fluorescent tube from the upper lamp holder. . Remove the tube from the lower lamp holder. . Remove
the transparent protective tube
reverse order
(see picture 8).
12. REPLACEMENT OF THE DOOR MAGNETIC GASKET
1
. Open the door.
2.
Take hold of the magnetic gasket with your hands and remove it from the frame.
3
. Insert the new gasket and press all around it when in place
* *
Operator's guide
3
. Ensure that there is no danger of explosion (AD) in the room.
2 Light switch:
to run the refrigeration system.
Thermostat:
to adjust the temperature inside the appliance. In order to
5 "SET" or "P"
6 "UP"
the temperature increases while pushing several times
.
2
. Refrigeration unit switch is on (green light lit up). . The
6
8
9
2
2
4
(NO LED) 6
. . Replace the fluorescent tube. . Replace everything in
7
2
. Remove the
a)
It is properly
c)
It complies with the
Notice:
in case the appliance,
to switch on the light inside the
4
.
Termometer:
to read the
the display will show the temperature of
4
3
3
7
(see picture 9).
I
UK
D
A
E
F
NL
P
5
.
Insert the
S
1 Rotation
DK
FIN
B
GR
CZ
3
EE
LV
LT
H
M
PL
SK
5
SLO
Publicidad
