Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLATION DIAGRAMS
C
onnexion of an a.c. lock release.
If an alternating current lock release has been installed, use a TF-104 transformer or an EL 502
dc/ac converter
and connect it to the lock release as it is shown on the respective diagram.
EL502 dc/ac converter and a.c Lock release
FA-PLUS/C
rev.938072
EL502
PRI
SEC
CN1
-
230110 0
-
-
+ +
CV-
CV+
Main
TF-104 and a.c Lock release
*
IMPORTANT: If the TF-104 transformer is used
to supply the a.c lock release and the door
panel lamps, wire ~1/~2 terminals of the
sound module with CV1/CV2 terminals
respectively of the EL-500SE module.
L
ink of several power supplies units.
If the quantity of monitors or telephones to be connected is bigger than the supported from one
power supply (see page 114), use additional power supplies to match the required quantity. The
first power supply should be connected to the door panel and to the first group of monitors or
telephones; connect the next groups to the positive terminal of its corresponding power supply.
To wire several power supplies link their ground terminals.
NEVER link positive terminals of different power supplies.
1st FA-Plus
2nd FA-Plus/C or FA-Plus
PRI
SEC
PRI
~
~
+ +
-
-
~
~
Main
Main
EL500SE
CN2 CN3
CN2
+
-
CV2
CV1
+12
AP - - +
+
Va.c
Lock release
TF-104
EL500SE
PRI
SEC
CN2
~ ~ ~ ~
-
CV2
CV1
+12
*
Main
Va.c
Lock release
SEC
+ +
-
-
To the second group of
monitors/telephones.
To the door panel & to the first
group of monitors/telephones.
137
138
E
xternal lock release activation.
The lock release can be activated at any moment by using an external push
button, that must be connected between 'AP' and ' ' terminals of the door
panel.
Door opening timed at 3 or 15 seconds, with the help of the dip switch SW1-2
(see page 108).
This function will allows to exit from the building being not necessary the use
of a key.
A
uxiliary devices activation with
Platea/Tekna Plus monitors.
To activate auxiliary devices the use of a SAR-12/24 relay unit will be required. If this device is shared
for all the monitors, link their A1 terminal and use just one relay unit. In case that each monitor
has its own application use a SAR-12/24 relay unit for each monitor and don't link the A1 monitor
terminals.
To activate this function, press
handset position.
Usual applications are the activation of stairs light, second lock release, ...
CN4
+
To distributor/
door panel.
( )
The neutral supply from the stairs light will be wired through the relay contacts SAR-12/24, the maximum current for stairs
*
light will be 1.8A.
The use of a TF-104 transformer will be necessary to activate a second lock release.
CN4
+
To distributor/
door panel.
OPTIONAL CONNECTIONS
–
monitor push button at any moment with no dependence of the
Platea Plus /
Tekna Plus
NC
NA
C
SAR-12/24
_
V
V
Malla
A
D
A1
IN
IN
in
out
Platea Plus /
Tekna Plus
NC
NA
C
SAR-12/24
_
V
V
A
D
A1
Malla
IN
IN
in
out
Door panel
AP _
To stairs light
push button
P
220 Vac/
( )
*
1.8A max.
N
TF-104
PRI SEC
~
~
~
~
Main
Lock release
Vac.
Publicidad
