Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
READ ALL INSTRUCTIONS BEFORE OPERATING AND RETAIN
INSTRUCTIONS FOR FUTURE REFERENCE
TURNING DIGITAL PROBE-PRO AND WORKLIGHT ON/OFF
1. Turn the probe on by pressing the Power On/Off Button
Turn the probe on by pressing the Power On/Off Button
2. When the probe is on, press the Power On/Off Button
3. To turn off the probe, press and hold the Power On/Off Button
than 2 seconds.
TONE MODE
4. Turn Digital Toner-Pro on by pressing the Power On/Off button
5. The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
and Wire Map Indicator
blinking, depending on whether the Toner is connected to a network port.
6. Set the tone mode to either digital toning or analog toning by pressing
Set the tone mode to either digital toning or analog toning by pressing
the Digital/Analog Tone Button
the Digital/Analog Tone Button
Digital Tone Indicator
One or both Analog Tone Frequency Indicators
analog toning mode. There are three frequencies available to choose from
when in analog mode: 1000Hz, 1500Hz, and 1000/1500Hz warble.
NOTE: When performing analog toning via the RJ45 port, the tone can be sent
down an individual pin, a pin pair, or to all eight pins simultaneously. To cycle
down an individual pin, a pin pair, or to all eight pins simultaneously. To cycle
thru the analog tone options, repeatedly press the Pin/Pair Selector Button
thru the analog tone options, repeatedly press the Pin/Pair Selector Button
to select the desired mode. The Wire Map Indicator
or pin pairs will be toned. When performing digital toning via the RJ45 port, the
signal is only sent to pin pair 3-6. Wire Map Indicator LEDs 3 and 6 will blink if
toner is connected to an active network port, otherwise LEDs 3 and 6 will remain
constantly illuminated.
TRACING PAIRED WIRES (FIG. 1)
1. Connect the Digital Toner-Pro's red
nnect the Digital Toner-Pro's red
respective Test Lead Inputs
2. Connect the red ABN Test Clip
Connect the red ABN Test Clip
Connect the red ABN Test Clip
Connect the black ABN Test Clip
Connect the black ABN Test Clip
Connect the black ABN Test Clip
3. Turn Digital Toner-Pro on by pressing the Power On/Off button
4. The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
, and Wire Map Indicator
T13 T13 T13
may be blinking, depending on whether the Toner is connected to
a network port.
a network port. When performing analog toning, check the "CONT"
Indicator
T4
NOTE: When performing Digital Toning, the "CONT" Indicator
not illuminate.
5. Select the preferred tone setting using the Digital/Analog Tone Button
6. Turn the Digital Probe-Pro on by pressing the Power On/Off button
7. At the far end of the cable, spread the wires apart at least 2" (51 mm), if possible.
8. If performing analog toning, first ensure the Digital Toner-Pro is set to analog
toning mode. Then ensure the Digital Probe-Pro is set to analog mode by
toning mode. Then ensure the Digital Probe-Pro is set to analog mode by
pressing the Analog Mode button
green when in analog mode. If performing digital toning, first ensure the
Digital Toner-Pro is set to digital toning mode. Then ensure the Digital Probe-
Digital Toner-Pro is set to digital toning mode. Then ensure the Digital Probe-
Pro is set to digital mode by pressing the Digital Mode Button
Mode Button will illuminate blue when in digital mode.
9. Use the Digital Probe-Pro to scan the cable's wire pairs. Move the Digital Probe-
Use the Digital Probe-Pro to scan the cable's wire pairs. Move the Digital Probe-
Pro's tip
slowly across the wires (FIG. 1). The Digital Probe-Pro's volume and
slowly across the wires (FIG. 1). The Digital Probe-Pro's volume and
slowly across the wires (FIG. 1). The Digital Probe-Pro's volume and
slowly across the wires (FIG. 1). The Digital Probe-Pro's volume and
P1
Signal Strength Indicator bars
pair. When the Digital Probe-Pro's volume and Signal Strength Indicator bars
are high over the first wire, low in the middle (between) the two wires, and high
over the second wire, you have located the pair of wires you are tracing. Use the
over the second wire, you have located the pair of wires you are tracing. Use the
over the second wire, you have located the pair of wires you are tracing. Use the
Volume Increase
6
OPERATING INSTRUCTIONS
LEDs 3 and 6 illuminated. The LEDs may be
LEDs 3 and 6 illuminated. The LEDs may be
T18 T18 T18
, will illuminate when in digital toning mode.
, will illuminate when in digital toning mode.
T13 T13
T20 T20 T20 T20
T14 T14
. If illuminated green, you may proceed.
P4
and Volume Decrease
and
P6
to cycle thru the different options. The
T7 T7
and black
T14 T14
T15 T15
to one of the wires of the pair to be traced.
to one of the wires of the pair to be traced.
to the other wire to be traced.
to the other wire to be traced.
T15 T15
LEDs 3 and 6 illuminated. The LEDs
LEDs 3 and 6 illuminated. The LEDs
T18 T18 T18 T18 T18
. The Analog Mode Button will illuminate
P12 P12 P12
+ +
will increase as it approaches the toned
will increase as it approaches the toned
P5
buttons to adjust the volume.
buttons to adjust the volume.
P7
once.
once.
P3
to turn the worklight on/off.
to turn the worklight on/off.
to turn the worklight on/off.
P3
P3
T9
will illuminate when in
will illuminate when in
T6 T6
will illuminate which pin
T18 T18
ABN Test Clip leads to their
ABN Test Clip leads to their
T9
P11 P11
for more
for more
.
,
T13 T13 T13
T10 T10 T10
.
will
T4
T7 T7
.
P3
. The Digital
Publicidad
